JB655DK6CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Vincent J Paola, from GREENWEL SPGS, LA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bad Line fault displayed on range clock
1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ivan from SNELLVILLE, GA
- Parts Used:
- WB24X25013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
when turn on the larger element would not come on, as the switch moves to the different settings it would light but not staying up.
remove the 4 screw from the back of the control panel take the knob from the front and remove the two screws then raise the rear panel cover up. you can pull the switch from there make picture note of where the plug ups are for replacement its cool
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dock from Aurora, CO
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The storage drawer came without supports.
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from TICKFAW, LA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Oven board went out
One wire at at time then used my razor blade to get front off stuck right back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SAN TAN VLY, AZ
- Parts Used:
- WB21X22134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not Reaching Temperature above 300 Degrees
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from CLAWSON, MI
- Parts Used:
- WB44X45494
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element was burned out.
unscrewed element from back of oven disconnected power source. Replaced new element & screwed new wires onto back of oven. Took 5 mins. Works like new. I am 73 yr old female so anyone can do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominick from THORNWOOD, NY
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven no longer working after running the self clean option. Only Stove top burners worked
I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.
To Install.
Reverse steps above
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.
To Install.
Reverse steps above
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from Lexington, OH
- Parts Used:
- WB30T10130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Outside portion of Element broken
First unplug range from electrical outlet!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from SAINT PAUL, MN
- Parts Used:
- WB02X38986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacing handle spacer
This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from JACKSONVILLE, FL
- Parts Used:
- WB04T10086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced oven door gasket
Remove old stained gasket and replaced with new. Only $57.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from RIVERVIEW, FL
- Parts Used:
- WB24X25013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Only one Burner was heating
Disconnect plug from outlet from stove.Remove nob from control switch rem 2 small screws to release switch.Go to the back and proceed to rem back panel with 1/4 nut driver.Pull out switch and replace one lead a time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from WEBSTER, TX
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Kidder, MO
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Hole in gasket
I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Calumet City, IL
- Parts Used:
- WB44X45494
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
8' ELECTRIC ROUND HEATING ELEMENT
THE TWO 8' ROUND HEATING ELEMENT
1. LIFT THE LID OF THE STOVE FROM THE SIDE. SOMETIMES YOU MIGHT HAVE TO PRY IT A LOOSE. BE CAREFUL HOW YOU LIFT IT FROM THE BOTH SIDES WITH A FLAT SCREWDRIVER.
2. BECAREFUL HOW YOU PRY THE WIRING FROM THE OLD HEATING ELEMENT. THE WIRING IS FRAGILE. REMEMBER THE STEPS YOU TOOK TO TAKE A LOOSE THE OLD ONE. I HAD MY SON TO HELP ME BECAUSE I FIRST PULL THE CLAMP BACK WITH THE SCREWDRIVER AND HAD HIM TO HOLD IT TO OLD ONE STILL HOOK UP TO THE WIRING. I PLACE THE NEW ONE IN THE CLIP. THEN I TOOK ONE WIRING AT A TIME TO THE NEW ONE.
1. LIFT THE LID OF THE STOVE FROM THE SIDE. SOMETIMES YOU MIGHT HAVE TO PRY IT A LOOSE. BE CAREFUL HOW YOU LIFT IT FROM THE BOTH SIDES WITH A FLAT SCREWDRIVER.
2. BECAREFUL HOW YOU PRY THE WIRING FROM THE OLD HEATING ELEMENT. THE WIRING IS FRAGILE. REMEMBER THE STEPS YOU TOOK TO TAKE A LOOSE THE OLD ONE. I HAD MY SON TO HELP ME BECAUSE I FIRST PULL THE CLAMP BACK WITH THE SCREWDRIVER AND HAD HIM TO HOLD IT TO OLD ONE STILL HOOK UP TO THE WIRING. I PLACE THE NEW ONE IN THE CLIP. THEN I TOOK ONE WIRING AT A TIME TO THE NEW ONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from COHOES, NY
- Parts Used:
- WB27X45466
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Bake button stopped registering
This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.
Was this instruction helpful to you?
Thank you for voting!