XGB635DEK3BB General Electric Range - Instructions

the tips you listed from; edward of Pipersville,Pa and Durwood of Suffield,Ct also Billie J of Western Grove, Ar were very helpful. Thanks to them & to you for posting them they were a time saver

removed bottom drawer, disconnected screws holding burner in place. unplug igniter. remove bottom tray from inside oven, remove 1 screw holding burner in place near door, remove whole burner assembly. take 2 screws holding element in place. screw new element to burner and reverse procedure. only tool i used was a 1/4 in nut driver.

replaced the glow bar ignitor

replaced the igniter by first removing the pan inside the oven, two screws in the rear. Igniter is attached to the burner with two machine screws, nut driver or small wrench is needed. Remove the lower drawer and un-clip plasitc connection located in the rear up high. Pull the wire and clip through into oven. Replace with new inginater, pull wires and clip through the back of oven and tighten screws, plug clip in, replace pan and plug in oven, done.

Remove botton pan of the oven to get at the igniter, remove bottom drawer to acess wires ,remove 2- screws from the igniter replace then replace oven bottom and drawer.

Researched problem came to conclusion that igniter was not staying hot (seemed to intermittently go on and off ). One connector and two screws problem solved and the cherry pies are back in my oven and ready for dessert! : )

It was so easy ! take out 2 screws , unplug old igniter, plug in new igniter, replace screws and turn on the heat!! Thanksgiving Dinner is back to my house with the whole Family!!!

Well first off ordered the part on Monday was here by Tuesday before I went to work. Was able to replace the part the next day and had pizza for lunch for me and the little woman.
Just also want to say Thank You.

Uninstalled the igniter and reinstalled the new one.

Repair was very simple. It was a five minute job including time taken to remove old part with a screwdriver and then it was a matter of plugging in the new part ant attaching it to the oven.

This job is done from the inside of the oven. Remove the drawer on the bottom. Open the oven and remove the bottom panel in oven which is fastened by two screws at the back. Lift up panel and pull foward to remove. Unscrew deflector plate and small plate that covers wiring hole. Remove ignitor from the burner. Replace ignitor. I found that you should also relpace burner at the same time. Burner usually causes the ignitor to go out. My burner had a hole in it and flames were shooting out directly on the ignitor which shortened the life of the ignitor. When you buy the burner it comes with an ignitor, you can't buy burner seperately but you can buy the ignitor seperately, so I recommend buying the kit.

used a clothes hanger wire to hold the plug in place so i could plug it in,was hard to get to the plug.but thank you it works fine now. didnt no how much i needed a oven till it was gone for three months.

installed the igniter as recommended by the web site.Fit like a glove. Works like a charm. Appliance repair would have been approx $140.00. Part plus shipping was right at $40.00. Made my day !!!

Replace the ignition heater. The only slight problem was fishing the connector down through.Works fine.

replaced igniter/replacement part was identical/remove door, just open and lift off, remove oven shelf's, broiler and broiler draw/2 bolts on bottom back oven floor release the floor panel, lift up on back, slide forward/2 bolts release the igniter from the burner tube/only attaches on one side of igniter/have to reach in back of stove bottom opening to release the old igniter wire feed at the plastic connector clip/used needle nose plier to hold stove end of clip to release/also removed right side small back rear cover panel(2 bolts)inside oven/plastic clip end was hard to fish through the gas tube and the back of the oven, pretty tight/pushed thru with screwdriver/can also pry the back oven wall back a bit to get the new one through the same path, little opening in the bottom back, then go back to the back of the stove opening and re-connect plastic clip connector from the ignitor wire to oven feed...