JSS26BD2BB General Electric Range - Instructions

I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.

Very easy, I'll probably try it again soon.

Took off the inside ( this allowed me to clean the glass) panel. Removed the two end parts with a screw driver. Replace the parts and we were good to go.

just replace the end cap with a new one all that was involue was to screw the new one in took about ten minutes and job done better than buying a new stove when the stove is still just like new. thank you for your on line help.

Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.

No longer carry the one to our stove so it was substituted with Nafisa on it. You could see all the electronics so we had to pry the old face off the old one blew it in place, but a clock was reversed from timer, but it works.

parts need to be delivered to do repair, its been over a month. customer service is not taking calls. I have paid for parts I did not receive.

I attached the end caps to my existing handle, but had to squeeze the parts together very hard to get them to mesh to the correct distance of the holes. I removed the screws holding outside frame of the oven door. I then opened the door fully, propping it up on my knee and removed the inside end cap screws. Placing the handle in position underneath the propped door, I attached the screws. Lastly I reassembled the door.

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

repair went fine, real easy.

The customer service rep was brilliant in finding the
right part number! It was sent the following day
(with email to let me know) The part itself was just
exactly like the old one. I simply turned off the power,
removed the 2 metal screws and unplugged the
broken element. The new one fit properly and works
like a million dollars. For about $50, you made me
look like a hero in my own house! Thjank you

Removed door from Oven.
removed screws from several components comprising the door and separated pieces.
Removed broken glass.
Prior to putting back together I took advantage of the convenience and used oven cleaner to clean inner portion of door. Installed new glass.
Reassembled door.

I followed the instructions given to me in the package and all went well. I cut the old wires off the burnt terminal block, stripped the wires, installed the wire nuts with the shrink rap, installed the new terminal block and burner. The new burner is working great! Thanks

I simply replaced the element. HOWEVER, the most wonderful parts of this repair...Because of the pictures and closeups and descriptions I knew exactly 'what' to order! And I had the replacement in less than 24 hours. I can do some home repairs but this company provided such detailed information AND speed of delivery...that this was a no-fuss fix. I'll definitely stop by to buy, again. Thanks!

First pull knob off switch. You may need a small screwdriver to gently start it. I then removed two screws, one in each end of control panel. Then rolled the panel up and out, as it is kind of hinged in the back. Removed two screws from switch front,layed it to the side and installed new switch. Removed wires (there were 5) one at a time with needle nose pliers, and placed on new switch. Replaced panel screws and was finished. Easy fix, quick delivery of part, I have used Partselect in the past and will continue.

We had to buy washers and screws to hold the handle on.
Then all we did was undo the screws that were on the side of the door. place handle on door screw the new screws and washers that we had to buy and replace the side screws and it was fixed.

The only problem that I found was that the handle kit did not come with screws or some kind of attachment to hold the handle on the door. We had to buy extras at the hardware store for that.