JB655FKBDS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- cynthia from CLAWSON, MI
- Parts Used:
- WB44X45494
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element was burned out.
unscrewed element from back of oven disconnected power source. Replaced new element & screwed new wires onto back of oven. Took 5 mins. Works like new. I am 73 yr old female so anyone can do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from LONGS, SC
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven door gasket needed replaced
Ordered the part, it arrived and 5 minutes later it a complete installation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from RIVERVIEW, FL
- Parts Used:
- WB24X25013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Only one Burner was heating
Disconnect plug from outlet from stove.Remove nob from control switch rem 2 small screws to release switch.Go to the back and proceed to rem back panel with 1/4 nut driver.Pull out switch and replace one lead a time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from JACKSONVILLE, FL
- Parts Used:
- WB04T10086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced oven door gasket
Remove old stained gasket and replaced with new. Only $57.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ivan from SNELLVILLE, GA
- Parts Used:
- WB24X25013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
when turn on the larger element would not come on, as the switch moves to the different settings it would light but not staying up.
remove the 4 screw from the back of the control panel take the knob from the front and remove the two screws then raise the rear panel cover up. you can pull the switch from there make picture note of where the plug ups are for replacement its cool
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from N CHESTERFLD, VA
- Parts Used:
- WB14X41386
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Oven door wouldn't close properly
Watched video on you tube. Removing/reinstalling all of the screws/bolts took longer than the actual repair.. Took 23 minutes total from turning power off, repairing and turning back on. Super easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caitlin from MOUNT SHASTA, CA
- Parts Used:
- WB14X41386
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Handle would not pull the latch back any longer
Super easy repair! There are videos online if you have one type of oven, I had the other type (with the little silver plate right above the latch part). The trick is to remove the handle from the assembly itself before removing or placing it in the oven. 4 screws total and I recommend needle nose pliers to help remove the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tiffany from Lexington, OH
- Parts Used:
- WB30T10130
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Outside portion of Element broken
First unplug range from electrical outlet!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from HAHIRA, GA
- Parts Used:
- WB14X41386
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Latch n handle to seal the oven during the self cleaning oven wore out and once engaged would not release
Remove the old oven latch and replaced it with the new replacement part. It was very easy to remove and replace with just a few nuts removed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Calumet City, IL
- Parts Used:
- WB44X45494
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
8' ELECTRIC ROUND HEATING ELEMENT
THE TWO 8' ROUND HEATING ELEMENT
1. LIFT THE LID OF THE STOVE FROM THE SIDE. SOMETIMES YOU MIGHT HAVE TO PRY IT A LOOSE. BE CAREFUL HOW YOU LIFT IT FROM THE BOTH SIDES WITH A FLAT SCREWDRIVER.
2. BECAREFUL HOW YOU PRY THE WIRING FROM THE OLD HEATING ELEMENT. THE WIRING IS FRAGILE. REMEMBER THE STEPS YOU TOOK TO TAKE A LOOSE THE OLD ONE. I HAD MY SON TO HELP ME BECAUSE I FIRST PULL THE CLAMP BACK WITH THE SCREWDRIVER AND HAD HIM TO HOLD IT TO OLD ONE STILL HOOK UP TO THE WIRING. I PLACE THE NEW ONE IN THE CLIP. THEN I TOOK ONE WIRING AT A TIME TO THE NEW ONE.
1. LIFT THE LID OF THE STOVE FROM THE SIDE. SOMETIMES YOU MIGHT HAVE TO PRY IT A LOOSE. BE CAREFUL HOW YOU LIFT IT FROM THE BOTH SIDES WITH A FLAT SCREWDRIVER.
2. BECAREFUL HOW YOU PRY THE WIRING FROM THE OLD HEATING ELEMENT. THE WIRING IS FRAGILE. REMEMBER THE STEPS YOU TOOK TO TAKE A LOOSE THE OLD ONE. I HAD MY SON TO HELP ME BECAUSE I FIRST PULL THE CLAMP BACK WITH THE SCREWDRIVER AND HAD HIM TO HOLD IT TO OLD ONE STILL HOOK UP TO THE WIRING. I PLACE THE NEW ONE IN THE CLIP. THEN I TOOK ONE WIRING AT A TIME TO THE NEW ONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Homosassa, FL
- Parts Used:
- WB02X33180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven will not heat
As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vilmar from TOBYHANNA, PA
- Parts Used:
- WB24X25013
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The two burners do not work perfectly because they are always turned on.
I took off the cover of the stove with a socket 1/4 mm, screwdriver and pliers. Now it works perfectly. thanks.../
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from MENIFEE, CA
- Parts Used:
- WB25T10102
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burnt out lamp bulb
Remove oven light lens cover, remove the bulb and replace it with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Buckeye, AZ
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water dumped over in in my overhead microwave, which dripped down on, & shorted out a burner switch.
My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- walter from townshend, VT
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven was not getting up to temp
Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.
Was this instruction helpful to you?
Thank you for voting!