PB935BP6TS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Frank from Marietta, GA
- Parts Used:
- WB30T10145
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Stovetop radiant burner went out
Turned off power at circuit breaker. Disconnected electrical connections from stove and lifted stove top out of counter. Removed glass top by removing about 8 screws from side of stove top.Replaced burner element and replaced glass top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- emmett from rocky mount, NC
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
F2 fault code kept appearing on oven
Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- randy from LORETTO, TN
- Parts Used:
- WB56X22160
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken inner window
Watched video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from NAPLES, FL
- Parts Used:
- WB30T10155
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
The center burner element of the large triiple burner was not working
The real challenge on this particular glass top range was to figure out which screws had to be removed to lift the glass top to get at the burner elements to do a replacement.
Removed the two side screws holding the control panel in place. Disconnected the two wire harnesses and took off the control panel to allow easier access. Then examined the screws attaching the vertical plate in front of the glass top. Most of them were on the on the vertical plate but a few were in the bottom of the horizontal plate. If successful, the vertical plate can be moved forward giving access to the glass top. You pull up on the front of the glass top and when it just clears the vertical front plate you pull the top forward a bit to get the back end of the top out of the read chrome vent piece. I then leaned the glass top up to about a 75 deg angle and then propped the top with a 24” wooden garden stake. I used two stakes to hold the top up. The challenge after that is to remove the old burner and carefully note the colored wiring and locations of the connectors and removed the three old clips. That took a bit of effort. several of the wiring harnesses were very short so you had to be careful when removing and installing the new burner. The burner has numbers stamped on the metal and you must note each number where the clips are located. The rest is to reverse the process. Some of the insulation pieces came off and some of the insulation clips fell off and you must be sure to get the insulation pieces back on in the correct location. Expect a lot of gunk that needs to be cleaned on the top and trim pieces. I save around $200 by doing my own replacement.
Removed the two side screws holding the control panel in place. Disconnected the two wire harnesses and took off the control panel to allow easier access. Then examined the screws attaching the vertical plate in front of the glass top. Most of them were on the on the vertical plate but a few were in the bottom of the horizontal plate. If successful, the vertical plate can be moved forward giving access to the glass top. You pull up on the front of the glass top and when it just clears the vertical front plate you pull the top forward a bit to get the back end of the top out of the read chrome vent piece. I then leaned the glass top up to about a 75 deg angle and then propped the top with a 24” wooden garden stake. I used two stakes to hold the top up. The challenge after that is to remove the old burner and carefully note the colored wiring and locations of the connectors and removed the three old clips. That took a bit of effort. several of the wiring harnesses were very short so you had to be careful when removing and installing the new burner. The burner has numbers stamped on the metal and you must note each number where the clips are located. The rest is to reverse the process. Some of the insulation pieces came off and some of the insulation clips fell off and you must be sure to get the insulation pieces back on in the correct location. Expect a lot of gunk that needs to be cleaned on the top and trim pieces. I save around $200 by doing my own replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jayne from EAST PEORIA, IL
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Needed to replace oven door gasket
Watched youtube video. Very easy to replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from FARMINGVILLE, NY
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Incorrect oven temperature due to defective temperature sensor.
Performed repair using a video for reference.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from San Antonio, FL
- Parts Used:
- WB48T10063
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
previous owner self cleaned and left oven racks in the oven
threw out the old ones and slide in the replacement ones from you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Kidder, MO
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Hole in gasket
I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Morgantown, WV
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Replace Thermostat
Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lung from PINEVILLE, NC
- Parts Used:
- WB30T10135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Did not function
It’s easy to replace and you can found out the video from YouTube to follow the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PHOENIX, AZ
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Stove overheated with an F2 error
Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from JACKSONVILLE, FL
- Parts Used:
- WB04T10086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced oven door gasket
Remove old stained gasket and replaced with new. Only $57.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman from WARWICK, RI
- Parts Used:
- WB24X47193
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The switch no longer regulated different heat settings, always on maximum heat.
Started by turning off stove circuit breaker on main electrical panel. Pulled stove out to allow access to rear panel, removed rear panel to access the infinite control switch. Next I took a picture to show where wires were connected to original switch. Removed failed switch from front panel, disconnected one wire at a time and connected them to corresponding connection on new switch. Reinstalled new switch to front panel and rear panel to stove. Pushed stove back in place and turned stove circuit breaker back on. Tested the new switch and all was working perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SAN TAN VLY, AZ
- Parts Used:
- WB21X22134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not Reaching Temperature above 300 Degrees
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from LONGS, SC
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven door gasket needed replaced
Ordered the part, it arrived and 5 minutes later it a complete installation
Was this instruction helpful to you?
Thank you for voting!