JGBP28DED1WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edward from WOBURN, MA
- Parts Used:
- WB03K10116
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Needed to replace on/off knobs on gas range.
The two knobs I received installed easily enough. The problem was that once I installed them, they sat horizontally rather than vertically as the original knobs did
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from The Villages, FL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
burners would not light
Remove the old tubes. Lift the lid NO MORE THAN FOUR INCHES. !!!!! Feel for the connections on the switch ends and attach losely. Carefully ( with some slight bending ) attach tubes to the burners. Tighten all connections. Do not over tighten.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Woodstock, IL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Front burners had to be lit with lighter
My son lifted up cooktop, unscrewed the front plate to gain access to old tube burners, removed and replaced with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICK from SAN JOSE, CA
- Parts Used:
- WB27K10141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
failed oven controller
Removed screws to back plate, unplugged, removed controller and installed new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from Locust Valley, NY
- Parts Used:
- WB15X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven handle broke off
Couple of screws and it was done. Simple and inexpensive since I thought I was going to have to buy a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Omaha, NE
- Parts Used:
- WB15X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Orignal oven door handle had multiple fractures and was fast becoming useless.
Removed the old handle with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Hauser, ID
- Parts Used:
- WB27K10141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
clock quit. Teperature was off.
Pulled range out from the wall. Un-screwed 4 screws. Disconnect old control board. Plugged in new board. Easy, easy, easy! We used the old overlay. It peeled off easily. If you want a new one, be sure and order it as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Venessa from Indianapolis, IN
- Parts Used:
- WB27K10141
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Thermostat shaft broken, doesn't maintain oven temp
Removed the back panel. Removed the electronic control board, four screws. Four electrical posts didn't match up exactly, but it wasn't too difficult to figure out because of labeling.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from CYPRESS, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Irvine, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced damaged oven rack
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Damaris from Easton, PA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing oven rack
I opened oven and pushed oven rack inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AL from PHILADELPHIA, PA
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
broken left /right range lines broke off
loosen the compression fitting both ends and screwed new ones in place .
Was this instruction helpful to you?
Thank you for voting!