GLMV168KB001 General Electric Range - Instructions

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

Fortunately I had my handyman here to repair a leak under my kitchen sink and asked him to replace the handle on my microwave. There were no instructions included with the handle but I had printed out descriptions from the web site of what others had done. He pried off the inside of the door which revealed two screws, which he removed. He then had to pry off another covering which revealed the other two screws that removed the handle. He attached the new handle and put the two parts that were pried off back on. It would not be an easy process for the ordinary householder and it would have been nice if detailed instructions had come with the handle (with pictures showing exactly which areas of the door needed to be removed). I was going to try the repair myself but am extremely glad my handyman was there as I probably would have ruined the microwave and would have had to purchase a new one. Kudos to my handyman.

Looked at schematic to see which parts became active when the power button was pushed. From there used meter to determine diode was open and capacitor was shorted. Biggest trouble was dis-assembly/assembly required to get to electrical parts.

I followed the instructions provided by others on-line who had done a similar repair. I removed a handful of screws, disconnected the wires from the old drive motor and connected them to the new drive, replaced the screws that held the drive motor in place, and those that held the bottom housing in place, and I was done. Literally took less than 10 minutes. If I had known earlier how easy it was, the microwave would have been fixed much earlier.

Must remove 5 screws in bottom of Microwave, which is hinged to the unit. Then simply remove the old lamp holders, and replace with replacements. Uses only a single screw for each lamp.

First, potatoe burned up in microwave. Microwave
was dead. Took off cover and found maintaince repair pamphlet in envelope. Schematic showed one shot thermostat for fire. Ordered thermostat from you and installed it. Works fine.

Unpugged microwave. Removed the screws on the bottom cover of the micorwave. Unpugged drive motor and removed two screws from drive motor. Installed new motor and replaced the bottom cover, plugged in microwave . . . presto!

Installation was just as easy as numerous other customers indicated. Also, your service was as great as many other customers indicted . . . part was recieved in 2 business days. Thank you for great service and website.

Removed Old Handle with minor difficulty, two screws came out easy other two had to drill out back plate to get to other two screws, after that, repair went fine.Took about an hour total time for repair, and sure saved alot of money!!

First I removed the screws that were underneath the microwave. Once I did that I disconnected the wires to the bulbs and removed the screws that were attached to the holder lamp. replaced the parts and reversed the process. It went really smooth.

Troubleshooting process:
Using a screw driver I opened the bottom of the unit using a Philips screwdriver and unhooked the drive motor electrical connector. Using a multimeter I checked to ensure power to the motor. This confirmed that the motor is bad and must be replaced.

Repair process:
After receiving new motor I removed the old motor and installed the new one using a Philips screwdriver and closed up the bottom cover.

It functioned good as new. Relatively cheap and very easy fix.

took a screw driver and pride off plastic on inside of door. be carfule not to break it. only one of two screws that go into handle were visable. had to drill a hole in metal braket to get at second screw. you can just bend the metal braket back inorder to use drill. bend it back when done. took off handle and replaced it. snapped plastic piece I took off back in place and finished.
ge told me i needed to replace whole door. which they nolonger stock and I could not find a whole door for my model on web. found handlw on this website and did it my self

My repair did not go so well. The screws for the handle are hard to get to, but since my handle was already broken i just broke it off the rest of the way. The problem I had was getting the outer door frame off. It is snapped on , and when I tried to remove it the glass broke. I think after years of use the glass and outer frame got stuck together. I hope this helps in your repair.

Ordered a replacement grill, replaced the optional charcoal filter at the same time. Took just a little effort to get the alignment tabs in place--required just a little more elbow grease than you'd think, then replaced the two screws.

I followed the exact details of one of your customers, removing the inner plate of the door, replacing the screws
that were left inside, into the new handle. I was finished in a few minutes and thank the earlier pioneer for his help.
I am a 75-year old grandmother and the help gave me the courage to try it. Very proud of myself.

Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware