CGLMV168KS003 General Electric Range - Instructions

I was very happy with the ease of finding the product I needed, the time it took to arrive and the fact that I received the right part. The replacement process was easy and only took about a minute.

I unscrewed the entire undersurface of the microwave (I didn't do this before!) and replaced the light socket. Easy job and I'm glad the part was still available.

Rather than open access door took off bottom (5 screws) This gave more room as the microwave is mounted under the wall cabinets over the stove.

First removed the inner panel. Use kitchen knife. Panel is snapped on. I could not remove hinge end so just pulled panel back. Two screws are then easily removed . Then the handle end top and bottom of outer panel must be snapped off. I could then get enough clearence to remove the two other screws which go thru outer panel only. I replaced the handle and reassembled in reverse order.

Found this site, was able to identify the specific part through the internal search engine, very user friendly.

Read what others had said about similar repair. Now with confidence, removed screws, got easy access to the motor, removed motor, installed new motor, re-installed bottom cover, done!

If you have electric burner or gas stove, I suggest laying down a towel or similar cloth. In the event you drop a screw, you done want it bouncing off the stove surface, or down into the burner dishes.

Great site, great resource, super fast shipping.

The hard part was trying to figure out how to get to the light socket. It is a bulb in the floor of the microwave that lights the stove top. I found help at your website by typing in the model number to find the diagram of the parts list which showed how each part fit together (and thus how they came apart). So I could see how to take the bottom off the microwebb and get to the wiring for the bulb and the bulb socket as well. They both had to be replaced with parts ordered from PartSelect along with the wiring. Putting in the new was just a reverse opposition. I saved $200 for a repairman, by spending about $60.00 for parts. Our other choice was a new microwave - and a repairman to install.

Ordering was simple Recieved part day after shipping. 3 days sooner than I expected.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.

I removed both sockets from the microwave and when your part arrived, I installed them both including the new lights. The work perfectly and it was very easy to put them in. I also appreciate the speed of delivery and your concern for my feed back on the product. I have you number in my contact list and should I need another part, I'll check with your first.
thanks you

Removed the 1 inch plastic frame on inside of door, gave me access to 1 set of screws. The problem I encountered was, getting to the set that holds the handle to the door.I didn't realize the metal frame held the outside with flexible hooks, therefore once u snapped them off, the outside with the handle on it HIT the floor glass and all!
Fortunately it didn't break. Supporting the outside is most important.

unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

Unplugged the stirrer motor and the noise stopped. Therefore, replaced the stirrer motor.

Remove screws holding bottom cover. Cover then swings down allowing access to the receptacles. Receptacles have a single screw attaching them to the appliance with a simple electrical plug supplying power. Very easy.

Must remove 5 screws in bottom of Microwave, which is hinged to the unit. Then simply remove the old lamp holders, and replace with replacements. Uses only a single screw for each lamp.

First, potatoe burned up in microwave. Microwave
was dead. Took off cover and found maintaince repair pamphlet in envelope. Schematic showed one shot thermostat for fire. Ordered thermostat from you and installed it. Works fine.