CGLMV168KQ001 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- MARILYN from SOLANA BEACH, CA
- Parts Used:
- WB2X9883
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
We couldn't install it - received wrong part.
The filter we have is 6x4. I ordered by phone.They sent the wrong part - 6x11.
We returned it to Post Office at our own cost - $8.85 May26. Tracked - it arrived May 28. So far we do not have the correct filter. We are waiting for the refund. Charged $49.99 plus tax & shipping of $7.75.
Thank you for helping us get the correct filter and a refund. We should not be charged for returning the wrong part they sent us by mistake.
Marilyn Tostado
We returned it to Post Office at our own cost - $8.85 May26. Tracked - it arrived May 28. So far we do not have the correct filter. We are waiting for the refund. Charged $49.99 plus tax & shipping of $7.75.
Thank you for helping us get the correct filter and a refund. We should not be charged for returning the wrong part they sent us by mistake.
Marilyn Tostado
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Waterford, WI
- Parts Used:
- WB08X10016
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Burned out bulb
Screwed in new bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Raleigh, NC
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Microwave Food Turntable Not Working
Reviewed the current postings surrounding the problem i was experiencing on your website. Located the 5 phillips head screws on the bottom panel. Removed them letting panel hinge down, removed the motor connector and checked for 21V AC with Volt Meter confirming the motor was not operable. Ordered replacement motor which arrived 3 days later during the holidays. Repeated the panel removal then removed the moter retaining screw and replaced with the received part a perfect matching. All in both panel removals for diagnostics and replacement of the motor took about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dorothy from Summerdalr, AL
- Parts Used:
- WB26X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Water had got on motor thru air vent, shorted out
Replace ventilator motor. No problem when you have correct part.
Thanks for the fast service.
Thanks for the fast service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Troy from Zieglerville, PA
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replaced drive motor on GE Spacemaker microwave
I thought this would be a major project but tured out to be very simple - 7 screws, 10 minutes and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Silver Spring, MD
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
glass cooking tray not rotating
Removed screws from bottom of microwave. Had to invite my neighbor over to remove one of the screws... he used his impact drill.
Found out that the motor was working fine. It was the brown piece that the glass cooking tray sits on that was broken.
I had removed the glass tray and tried to pull out the brown piece...but, it wouldn't come out and so I assumed that it was intact and thought that the motor wasn't working.
It's great that it's so easy to return parts to PartSelect.
Found out that the motor was working fine. It was the brown piece that the glass cooking tray sits on that was broken.
I had removed the glass tray and tried to pull out the brown piece...but, it wouldn't come out and so I assumed that it was intact and thought that the motor wasn't working.
It's great that it's so easy to return parts to PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Ludington, MI
- Parts Used:
- WB08X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bulb broke in light socket
Tyring to get bulb out i ruined the light socket. Unscrewed the bottom cover of microware. Took out screw holding light socket, removed wires to socket with pliers, intsalled new socket. It was a piece of cake and the part was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Plymouth, MI
- Parts Used:
- WB26X10038
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noisy cooking tray while spinning
7 screws, lowered the bottom and replaced the motor with two more screws. It was fairly easy and I'm pretty proud of myself.
The installers grouted in my above the top microwave so the bottom didn't hinge down as easily as it should have. But it worked.
The installers grouted in my above the top microwave so the bottom didn't hinge down as easily as it should have. But it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CELIA from TINLEY PARK, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Glass Tray Quit Spinning
First I removed the 6 screws that hold the bottom of the microwave . I was able to see and get to the cooking tray drive motor. I removed the 2 screws and took out the motor. I replaced the motor and replaced all the screws. Started the microwave and it worked , no problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Cary, IL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
motor that rotates glass cooking tray was not working
Disconnect the power cord. Removed the screws locate under the spacesaver microwave. The bottom will swing down and hang off the hooks on the back edge. Disconnect the wires plugged into the broken motor. Remove the two screws that hold the broken motor in place. Replace with new motor and re-insert screws and motor wires. Reassemble bottom panel and plug power cord back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zayne from Blanchard, OK
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Cooking Tray stopped turning, motor rattled
Removed the screws holding the bottom cover on, removed screws holding motor in place, replaced motor, put everything back in. Simple as changing batteries.
The nice thing is that PartSelect, as always, delivered exactly what I needed and very fast. Ordered on a Wednesday and received it on Thursday (the very next day!)
The nice thing is that PartSelect, as always, delivered exactly what I needed and very fast. Ordered on a Wednesday and received it on Thursday (the very next day!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lake Sherwood, MO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The turntable began operating intermittently and making noise
The repair was extremely easy. Remove seven screws in the bottom trim, slip the electrical connector off and remove the two screws holding the motor. Slide the new motor into position, replace the connector and screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Colorado Springs, CO
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Turntable motor quit working
As others have desribed - remove 5 screws from the bottom cover. Lower cover and replace turntable motor with 2 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheldon from Boca Raton, FL
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Water over flow killed Tray Drice Moter
Removed filter, removed five (5) screws, lowered lower pan, disconected feed wire, removed screw holding the moter, twisted old moter out. Twisted new moter in, replased screw, conected feed wire, closed pan, replased five (5) screws, replaced filter. Tested microwave with glass of water in it.
All went well.
From part order to finish was less then five (5) days.
The price was about $50.00. The people that sold it to me sugested I buy a new one because it would cost as much to have a service call and part as it would be to replace the microwave.
.
All went well.
From part order to finish was less then five (5) days.
The price was about $50.00. The people that sold it to me sugested I buy a new one because it would cost as much to have a service call and part as it would be to replace the microwave.
.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Canal Winchester, OH
- Parts Used:
- WB26X10038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Micro Glass Tra Y Quit Rotating.
Took out the screw holding the old motor, unpluged it and reversed the procedure to install new part. My wife is now very happy!
Was this instruction helpful to you?
Thank you for voting!