CGLMV168KB003 General Electric Range - Instructions

I initally thought the problem was the turn table motor but after installing that motor & not being successful I realized the problem was the stirrer motor.Removing & insalling that motor was a bit more challenging but worth the effort as I saved either the cost of a repair technician or the puchase of a new one.The microwave is back in service & running fine.

After finding the part on PartSelect, ordering it online, receiving it quicker than expected -- it took me 5 minutes to unscrew the bottom cover of the microwave, take off the old motor, replace with the new motor, screw the cover back on and test the WORKING cooking tray drive motor.
Very impressed with the efficiency of PartSelect. It's web page was easy to navigate. Thanks.

I looked up the parts of the microwave on Part Select to see if there might be something I might be able to do myself. I found that the Cooking Tray drive motor was the problem. I ordered the part and got it the very next day. I loosened the 6 screws to the lower part of the microwave and then the two screws that held the part in place. I removed the element and pulled the wire plug from the element, placed the new element back in with the screws, repluged the wire, placed the lower cover back to the microwave, tested the microwave out and, is still working quietly as if it were new. Thanks to part select.com it was easy.

I was very happy with the ease of finding the product I needed, the time it took to arrive and the fact that I received the right part. The replacement process was easy and only took about a minute.

Rather than open access door took off bottom (5 screws) This gave more room as the microwave is mounted under the wall cabinets over the stove.

I unscrewed the entire undersurface of the microwave (I didn't do this before!) and replaced the light socket. Easy job and I'm glad the part was still available.

Found this site, was able to identify the specific part through the internal search engine, very user friendly.

Read what others had said about similar repair. Now with confidence, removed screws, got easy access to the motor, removed motor, installed new motor, re-installed bottom cover, done!

If you have electric burner or gas stove, I suggest laying down a towel or similar cloth. In the event you drop a screw, you done want it bouncing off the stove surface, or down into the burner dishes.

Great site, great resource, super fast shipping.

The hard part was trying to figure out how to get to the light socket. It is a bulb in the floor of the microwave that lights the stove top. I found help at your website by typing in the model number to find the diagram of the parts list which showed how each part fit together (and thus how they came apart). So I could see how to take the bottom off the microwebb and get to the wiring for the bulb and the bulb socket as well. They both had to be replaced with parts ordered from PartSelect along with the wiring. Putting in the new was just a reverse opposition. I saved $200 for a repairman, by spending about $60.00 for parts. Our other choice was a new microwave - and a repairman to install.

Ordering was simple Recieved part day after shipping. 3 days sooner than I expected.
Removed bottom panel. Removed 2 screws holding motor. Pulled out motor. Replaced with new motor. Reinstalled 2 screws, Put bottom panel back in place. The easiest repair I have ever done.
Have bookmarked your web page. When I need another repair part, this will be the only company I would consider doing business wth.

I removed both sockets from the microwave and when your part arrived, I installed them both including the new lights. The work perfectly and it was very easy to put them in. I also appreciate the speed of delivery and your concern for my feed back on the product. I have you number in my contact list and should I need another part, I'll check with your first.
thanks you

Unplugged the stirrer motor and the noise stopped. Therefore, replaced the stirrer motor.

Remove screws holding bottom cover. Cover then swings down allowing access to the receptacles. Receptacles have a single screw attaching them to the appliance with a simple electrical plug supplying power. Very easy.

unplugged power cable / unhooked front vent / unscrew the monitor panel / slide up to dislodge / take the fuse out and put in the new one in / fuse is located right in front of monitor panel once its open might be covered by wirings / you can unpin the cables from the panel to make it easier for you just make sure to put it back properly or you can have somebody hold the panel for you. Installing the fuse is easy waiting for the parts is crazy......

One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.

Fortunately I had my handyman here to repair a leak under my kitchen sink and asked him to replace the handle on my microwave. There were no instructions included with the handle but I had printed out descriptions from the web site of what others had done. He pried off the inside of the door which revealed two screws, which he removed. He then had to pry off another covering which revealed the other two screws that removed the handle. He attached the new handle and put the two parts that were pried off back on. It would not be an easy process for the ordinary householder and it would have been nice if detailed instructions had come with the handle (with pictures showing exactly which areas of the door needed to be removed). I was going to try the repair myself but am extremely glad my handyman was there as I probably would have ruined the microwave and would have had to purchase a new one. Kudos to my handyman.