JGBP92SEM1SS General Electric Range - Instructions

At first I didn't believe it was the igniter due to the fact that it was lighting up, but after reading some of these post, I thought I would give it a try. I accessed the igniter from the broiler drawer after taking out the pans. I removed two bolts with my nut driver and disconnected the wires at the plastic connector after removing the heat shield with a phillips screwdriver (1 screw). I also had to remove a clip to get the wires to pull threw the back of the stove. Here is where the fun began...While waiting on the part to arrive, I decided that it would be a good time to thoroughly clean the entire unit. During this process, I lifted the top of the range to far and cracked both front burner gas lines. After running around town trying to find the gas lines with no luck, I returned home and ordered them from PartSelect as well. The igniter arrived one day and the gas tubes the next. I reassembled the unit and everything works like new, thanks to PartSelect. One other note, when my igniter arrived, It had the exact same electrical plug that my original one had. Some of these post said that you would have to cut the connector off and use the porcelain wire nuts provided. The parts I received were manufacturer parts, no off brand replacements. Again Thank You PartSelect.

Took out bottom of oven, took apart burner & cover. Replace the igniter, , put back together. BAM

My husband replaced it within 15 minutes,was easy. We ordered the part on a Sunday and had it by Tuesday. Very fast.

thank you

This is a wall mounted oven. Quickly removed the door off hinges (no tools needed). Removed two mounting philips head screws from old igniter. Pulled on wires from the old igniter from back of oven to expose connectors. Disconnected the old igniter. Because the new igniter had a different type of connector, I had to cut connectors off the oven wires as well as the new igniter and use the provided wire nuts. I stuffed the wires back into the back wall of the oven and repositioned the insulation, secured the new igniter and put the door back on. Job done, oven works fine.

Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete

Removed lower oven panel and replaced oven igniter.

Needed to replace the part in oven which lights the gas. My husband is more of a supervisor rather than a fix it yourself kind of guy. But he did it and it was hilarious watching him squeeze in a place meant for a smaller person with tiny hands, while holding the flashlight in his mouth. But the oven is fixed and works like brand new. Thank you

Although the original oven design called for a round igniter, the most recent replacement, done by a service mechanic, utilized a flat igniter. I compared the appearance of this flat igniter to the igniters offered by PartSelect and found that the GE igniter (not the Roper which cost twice as much) matched exactly. I installed it and that solved the problem (of insufficient igniter heat to turn on the gas).

Removed oven door and warming tray. Then removed two screws holding the igniter in place. Disconnect the plug visible below the oven after warming tray removal. Installed new igniter in reverse order.

I was sure happy that they thought to add in the ceramic wire nuts. This Hotpoint stove had a direct wire, no wire clips like the new part had. I cut the wires and used the enclosed ceramic wire nuts. The stove works great. Parts Select helped in locating the model number which made this transaction a smooth one. Thanks. Always remember to turn off gas line and unplug any item you work on.

Had to use the wire nuts because the plug did not fit.
I used the old plug and spliced the wires.Thanks for the ceramic wire nuts.

two 1/4 inch screws took oven tray out....two 1/4 inch screws took out ignitor..the replacement would not plug into the wiring, so I cut the plastic plug off and wire nutted ends together..baked cookies after!!!!

I got my part in a couple of days during christmas and still got at pretty quick it was 5 screws unpluged the old one pluged in the new one put screws back and we were ready to cook, did all from inside the oven did not even move the stove very simple!!

The part was the exact replacement and fit exactly. Had to cut some of the sheetmetal at the back of the broiler to get the wiring through.

removed the screws that held element in place, pulled out old igniter and replaced with new one.