JB770TP2WW General Electric Range - Instructions

This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.

No parts dealer had a window for this particular oven door. But the associate at Part Select helped me find one that was the right dimensions. The internet videos I found describing installation of a GE oven glass window all described a glass held in place with brackets that don't exist on this model. The broken window was obviously held in place by adhesive. I found a video showing installation a Whirlpool oven window. The construction of the door seemed very similar to mine and the video explained how to attach the window inside the door with high temperature resistant double sided tape. I used Gizhome 3M Double sided Tap. I set door flat on a table unscrewed all the screw (two different size torque screws and 3 screws with nut tops) that held the outer cover to the door. Then I used a putty knife to scrap the old adhesive from the outer door frame. The top of the window is held in place by the metal panel behind the oven door handle. In order to slip the glass under the metal panel I slightly loosened two small screws that held the metal to the door frame. When the door handle is reinstalled it will hold the panel in place. I attached a strip of double sided tape across the entire area that I had scraped adhesive from. I added a short strip of double sided tap on both sides of the window frame, (I'm not certain that was a good idea). I carefully slipped the glass under the metal panel and lowered it to the frame while watching for exact fit. When I tightened the large door handle screws they tightened the metal snugly against the glass. I clamped the glass to the frame at the bottum and placed several bottles of water as weights along the sides of the frame and let the adhesive cure for 24 hours. The project took me several hours because of all the research I had to do. I was thankful for the parts associate's help finding a comparable window.

This went pretty smoothly. Watch the video and just follow along step-by-step and it goes well. It would have only taken about 30-45 minutes (even being careful and slow) but I ended up placing the glass twice (be very careful and triple check that all the insulation gets poked under the housing and none is sticking out). The first time I had a small piece sticking out. (Use gloves for this part so your hands don't itch). The second time I needed to redo part of it is I forgot one of the spacers on the door handle and had to get that in there so the handle worked properly. I also took the time to clean the oven while the door was off so that took some time. Total I probably had 1.5-2 hours into this project but at least half of that was me cleaning and being fussy. This is an easy repair. I'm not a confident repair person and this wasn't difficult. It was a little time consuming but well worth the cost vs calling a repair person or buying a new appliance. You do need to have a specialty star head on a screwdriver but my simple tool kit had all the tools I needed. The oven has been working great since the repair.

First of all, there are FOUR panes of glass on the oven door and two different sizes. Make sure you're ordering the right pane. We initially got the wrong one and had to return/reorder.

Took door off hinges and set on table. Removed almost all screws. Two at the top are very long and almost spring loaded -- this was helpful when putting it back together.
When removing the layers, keep track of what/where screws are placed. Some are star-hole-head, some are hex-head (socket). Work slowly and carefully so as not to break additional panes of glass. Leave plenty of room in your workspace to set items aside while you get to the innermost part of the door.

For this part #, it's deep in the door layers and surrounded by fiberglass. Wear gloves so you're not itchy later. This part acts as a double-pane with a narrow aluminum frame around the two pieces of glass. Be careful not to bend the frame when removing the broken piece. One corner of the frame also has a hook-n-hole closure. Take care to not bend the hook too much.

We wiped all the glass pieces off to get all fingerprints, smudges, and baked-on foods removed. Then we put the pieces/parts back -- a lot like a puzzle. Had the oven back up and running with no problems. It may take two people to get the door back on the hinges just because of the weight and awkward position they need to clamp back together.

First unplug range from electrical outlet!
Removed screws under front edge of stove top, propped it open with long paint stick, pried clips off of the element, unplugged and plugged in new element, push element back into clips, closed top on stove, plug back into socket, tested new burner, put screws back in under top front edge of stove top!!!

Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.

First, the part was an EXACT fit - what a relief. Thanks PartSelect! Teh oven door had to be taken apart a bit, but once I found the right nut wrench, it went smoothly. Having another set of hands really helped.

Took top of stove off, disconnected the heating element, re-installed the new element and now my stove works fine.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

It was easy, it just fit in. I was afraid the part might not be right or that I would need extra parts but everything was great. Part arrived in 3 days. thanks

Changed out the burner with a new replacement and it still didn't work. The socket on the old burner had a burn mark on it. The infinite switch operated sloppy not crisp like the other burners.Ordered a replacement online. Moved the range away from wall and cabinet and shut off electric at panel box. Removed upper back panel. removed switch knob and 2 screws holding switch. Compared electrical connections of both switches and saw that they were different. Read instructions which were included with new switch and found diagram for connecting old lead to new lead correctly. After all leads were connected, remounted new switch powered up and tested OK.

Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.

Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!