JB660DM1WW General Electric Range - Instructions

Replacing the gasket is easy and requires no tools. Pull out the ends that are just inserted in their slots. Then work your way around the door pulling out the little metal clips from their holes. Replace the new gasket the same way.

It's even easier to do if you remove the door first and place it on a table--but it's heavy. To remove the door, flip up the hinge clips--you might need a flat screwdriver to do this if they are old and stiff as mine were. Then close the door almost all the way--you'll feel a stopping point-- and pull up. It comes right out--but again, it's heavy.

Replacing the bake element is not much harder. It's easier to do with the door off, but not impossible with the door on. First, pull out the range and unplug it. Then, remove the hex screws holding the bake element against the back wall. The element has two electrical contacts that insert into clips at the ends of wires. Pull out the wires a bit to give yourself some slack, then pull the contacts out of the clips. Insert the clips from the new element into the wires and replace the screws.

If the wires get lost behind the back wall of the oven, it's not a big deal. Just remove the narrow central panel on the back (it has six hex screws) and push the wires back through the wall opening. Then replace the back panel and install the new element.

After reading all the repair stories I knew that their wasn't any extra wire when the old element is removed. Well, even with that knowlage one of the wires came loose and slipped back in. Fortunately I was able to remove a panel in back and push it back through. I was afraid I would have to take off the whole back but instead there is a panel covering the wire running down the center of the oven. After removing 5 screws with the same nut driver as the one for the coils I had it done in minutes. I had no problem and I am NOT a 'do it yourselfer'. Oh, did I mention I ordered the part on Friday and received it on Saturday standard shipping? Pays to live the next state over from the place shipping it.

Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.

Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.

Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.

loosen interior panel of oven with star driver. Removed broken arm. install inner screw and then install final screw to both panels and handle.

The inner screw mount only through the exterior door only making it tricky to line up the final bolt which goes through both panels and the handle.

Other than that it when smoothly.

1- opened oven door
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top

The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws

The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years

Replaced control panel after removing original control panel facing with heat gun and Wala

I unscrewed and removed the old element from inside the oven, but unfortunately there wasn't enough extra wire to pull through and attach the new element from the front, so I had to move the oven away from the wall, remove the back panel, and connect the new element from the rear. Very self-explanatory.

The new element had some kind of spray or coating on it that caused some smoke for a few minutes, but then it worked fine.

Consult the instruction guide that comes with the new part. Excluding doing some cleaning while things were apart, the operation took about 20minutes. 1. Open the oven door all the way. 2. Pull back the hinge latch on each hinge. 3. Close the door partially (about broil position). 4. Remove door by pulling so that hinges com out of the slots. 5. Carefully set door face down on a table so that inside of door faces up. 6. With a Torx driver, remove 2 screws at upper part of inside of door. 7. With a nut driver, remove screws at bottom of Door Bottom Channel Trim. 8. Lift inside of door off, being careful not to lose the spacers that are behind the door panel at the upper part of the door. 9. With the nut driver, remove 4 screws that hold bottom trim to the side trim pieces. 10. Remove the old trim and replace with the new. 11. Align the left, right, and bottom trim pieces. 12. Reattach the 4 screws that hold the bottom trim to the side trim pieces. 13. Carefully replace the inside door panel, making sure the spacers are aligned properly between the main door pieces. 14. With the Torx driver, replace the 2 screws at the upper part of the inside of door. 15. With the nut driver, reattach the bottom screws at the bottom of the trim piece. 16. Carefully reinsert the door hinges into the slots (the door must be in the approximate broil position). 17. When hinges are properly inserted, door may be opened all the way. 18. Push the hinge latches back into hinges to secure door to oven.

I am not the handiest person in the world, and this repair was easy even for me. If you suspect that the temperature sensor is the problem, do yourself a favor and buy this inexpensive replacement part and install it yourself prior to calling a professional who will charge a service fee just for checking it out. Pull your oven out from the wall so you can access the back. Unscrew the small nuts on the back to remove the sheet metal cover. Find the wire that goes to the sensor and unplug the plastic coupling. In the oven, unscrew the one nut that secures the sensor to the back wall of the oven. Pull the broken sensor out and replace it with the new sensor. Feed the wire through to the back and plug the new sensor into the same wire that was just disconnected. Reinstall all of the nuts. Do a "test cook" on some frozen food to ensure that the temperature seems correct (i.e., does it cook as expected in the recommended amount of time). The actual repair takes less than five minutes. I put "30-60 minutes" to account for unplugging the oven, pulling it out, removing the screws, replacing the screws, pushing it back in, and testing the temperature.

Read the instructions on how to remove the door, found in the owners manual. Once you release the hinge lock latches, the door can be lifted off of the hinge arms.

It is fairly heavy and bulky. I spread a large towel on the kitchen table and placed the door, front side down on the towel.

Remove the 3 nut screws at the bottom of the door and then lift the inner door assembly up about 3" and hold it up temporarily with a medium sized plastic food storage container. This will allow room to access the 4 nut screws (2 on each side) that secure the trim to the door.

The old trim was somewhat difficult to remove because of years of rust and other build up where the front door glass goes behind the trim. Be careful not to damage the glass. I used a putty knife.

The edge of the glass will be soiled so I used a mild abrasive cleaner to remove the rust and grime, and then used a window cleaning spray to clean the glass.

The new piece had to be "fitted" slightly to match the existing screw nut holes but it goes together quickly.

Replaced

Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.