JBP61BD2WH General Electric Range - Instructions

My husband had already removed the back plate form the stove and detached the wires from the old burner switch because it was keeping the burner on. He unscrewed the old switch and removed it. He then popped in the new switch, attached the wires to the correct contacts, and put the back plate back on. We plugged in the stove, and that burner works good as new.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.

turned electricity off, removed element using a screwdriver had to take the back panel off, attached new element put stove back and tried it out and it worked probably 20 minutes. Also need to comment that was totally shocked how fast the element was shipped to me, ordered the part in the p.m. and it was here not the next day but the next ....awesome

Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.

I have a GE Profile oven and the heating element on the bottom broke in two. I found the part on your website very easily. It was easy to see that I had the correct part. I ordered the new element and it came in about three days. I easily took off the old element, but I was really surprised because the new one didn't fit. The heating element itself was the correct size, but the holes didn't quite match up. As a matter of fact I had to take some tin snips and expand the hole at the back of the oven. That was the only hard part, but it was really difficult to lean in that far without putting too much weight on the door. Anyway, I opened the hole about an inch more, plugged it in, and now it works perfectly!

removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in

Isolated to control switch.

Replaced

verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you

Used the TS guide, because I had no idea what the problem was. That was easy step by step. Thanks. Gave me a list of two parts that could fix the problem. Picked the higher percentage part (97%). Followed the simple install instructions and it was successful. One problem I did encounter was the two wires that it connected to were short. Removed the back center plate to gain access to the wires. I was able to extend them enough to make the connections to the bake element. If not for that the repair would have only taken maybe 10 minute's.

I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!

Difficulty was in determining the right model number and part number of a switch. Noted that the left front burner came on when the switch for the left back burner was turned on. By inspection I found the left front burner switch had become faulty by actually hearing an electric arc in the switch and smelling the oder in the switch. With help from the person I called I was able to determine that the Model Number on the actual stove was wrong. It had an extra 0 between the W and F which she said was a common error in the GE model number. I then gave the switch number I found on the switch to the contact person and she was able to verify the right part number. It was relatively easy to replace the switch by taking off the back upper plate then taking off two screws that held the switch to the stove. The part came quite quickly once ordered. Sears repair wanted $75 just to diagnose then the cost of the part. I got the switch for $69.