JBP61DB1WH General Electric Range - Instructions

already had the old one disconnected (spade ends) on old element, new one arrived installed it the same way I removed the old part, just 2 little screws to hold it in place, after you reconnect the spade ends. Then plugged the unit back in. Always use common sense when working with electrical appliances! Easy as the pie I can now bake.

The only problem was m short arm and no good flash lights around

I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

replacement was easy. pulled away the stove from wall. unplug the stove. open oven door. remove the two hex head screws holdings stove top. raise the stove top in the front. supported stove top with a 16 inch piece of wood. place New Burner under old burner. remove old burner remove wires remove old burner and place it on top of new burner connected the wires from burner to new burner. install new burner. remove support lowered top down. plugged in stove tested. .burner. burner w.ork fine. reinstall hex head screws back top. pushback stove back into the wall. testes over again. all the stove work done.

My husband was able to easily remove and replace the switch and know with-in 15 minutes.

It took longer to get the new element out of the box than it did to install it. I removed the two screws with a 1/4" nutdriver, pulled the element out roughly three inches, unplugged the connectors and discarded the old element. I did the reverse to install the new element.

Removed old; inserted new.

Removed two screws, pulled old element forward 2 inches, removed two wires. Pulled old element out of oven. Put new element in oven, attached two wires, pushed element all the way in, put two screws in and tightened them. Turned oven on to test new element. Element worked. Project completed.

I took a chance and guessed that the problem was the element, as opposed to a thermostat or other part that may have failed. (Oven was made in the 70's) I entered the data for this old oven on the PartSelect.com website and it came up with a part for me to order. When I received the replacement element, I noticed that it was not "exactly" the same shape as the old part, but the dimensions were correct and it fit into the space on the bottom of the oven without any problems. The dimensions of the connectors were pretty close to exactly the same as the old element, and the screw holes in the mounting plate lined up perfectly with the corresponding threaded holes in the back wall of the oven - it took me less than 15 minutes to install the part and the oven appears to be working perfectly again.

The repair went very smooth and easy it took me around 10 minutes to replace part and I was ready to bake again

Unplug the old one and plug in the new one. Nice and easy.

Removed the 2 screws, unpluged the 2 wires and installed the new elment

I disconnected the power to the stove and it was very simple, undid the nuts with socket wrench pulled element out and diconnected the wires.I put the new element back in the same way the old one was removed .I am a 70 year old woman.The great part was the element was shipped out vey quickly! great service

Required new light lens for oven this type has five (5) of them; only the oven temp light lens was damaged. Ordered from Parts Select.com received item fast in seven days. removed rear guard plate, than oven temperture switch than slid the neon light switch off of the light lens.Lens is removed from the front panel. Installation is reverse order.