JS900CK3CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- NICK from Vernon, CA
- Parts Used:
- WB48T10068
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic guide Broken
replaced Plastic Guides
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Murrells Inlet, SC
- Parts Used:
- WB04T10050
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door gasket was soiled
took out old gasket and inserted new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Zachary, LA
- Parts Used:
- WB23T10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake and convection cycles quit working after a10 minutes
Unbolted temperature sensor from back of oven. Disconnect cable connector. Replaced and reconnected new sensor and bolted back in place. Haven’t had to replace bake element yet, but it’s a major job being this GE Profile oven has the bake element hidden. That’s a new one on me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudene from ORCUTT, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks old and ugly
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from ARROYO GRANDE, CA
- Parts Used:
- WB44T10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Remove and replace Broil (upper) heating element.
Turn off the power to the oven. (There should be a circuit breaker in the main power panel dedicated to just the oven) (the oven should be cool to the touch).
Open and remove the door by pulling it up and off the hinges (this is best accomplished with a helper).
Remove the racks (wire shelves).
Remove the two 1/4" mounting screws that secure the heating element to the back and the two screws that secure the element to the top of the oven..
Gently pull the wires out and disconnect them from the heating element.
Now reverse the process.
Connect the wires to the new heating element in the same fashion as they came off.
Push the wires and heating element back in place and secure with the four screws.
Replace the wire racks (shelves).
Replace the door (again, this is best accomplished with a helper).
Turn the power back on.
Run a test of the broiler to make sure the repair was completed properly.
voila!
Open and remove the door by pulling it up and off the hinges (this is best accomplished with a helper).
Remove the racks (wire shelves).
Remove the two 1/4" mounting screws that secure the heating element to the back and the two screws that secure the element to the top of the oven..
Gently pull the wires out and disconnect them from the heating element.
Now reverse the process.
Connect the wires to the new heating element in the same fashion as they came off.
Push the wires and heating element back in place and secure with the four screws.
Replace the wire racks (shelves).
Replace the door (again, this is best accomplished with a helper).
Turn the power back on.
Run a test of the broiler to make sure the repair was completed properly.
voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from PARKER, CO
- Parts Used:
- WB44T10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Lower Oven Broiler Stopped Working
Turned power off to oven
Unscrewed broiler nuts (total of 4)
Pulled Broiler out from back of stove
Disconnected wires
Reconnected wire
Remounted broiler and replaced bolts
Turned power back on
Unscrewed broiler nuts (total of 4)
Pulled Broiler out from back of stove
Disconnected wires
Reconnected wire
Remounted broiler and replaced bolts
Turned power back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vilas from HANOVER TWP, PA
- Parts Used:
- WB30T10132
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Back burner was not working.
Took top of stove off, disconnected the heating element, re-installed the new element and now my stove works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Homosassa, FL
- Parts Used:
- WB02X33180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven will not heat
As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne Marie from Andover, MA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old dishwasher rack and silverware rack
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Newark, DE
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Range lower drawer would not stay on track.
Easy to install replacement parts using the screws provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Philadelphia, PA
- Parts Used:
- WB30T10129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner not operational.
Disconnected power supply. Removed damaged element by releasing retainer clips and unplugging wire contacts. Replaced with new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from Deer Park, WA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken drawer support
Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from CYPRESS, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!