JBS160DM4BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Curt from Maple Grove, MN
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner light would not shut off
Checked each burner switch by disconnecting the light indicator wire. Located the switch, replaced the switch and the indicator light operated as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Jericho, VT
- Parts Used:
- WB24T10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner was always on high when on.
Disconnected the power. Removed hex head screws from top and lower rear panel. I think there were 8 all together. Pull the knob of the burner control, removed two screws that held the switch in place. Moved the wires one at a time to the new switch, re-assembled. Burner worked properly. Very easy to find the right part from this web-site, and the instructions from others like this were helpful. Easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from Bellows Falls, VT
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
heating element blew apart
I watched the video on this website and it couldn't have been easier. The only thing I did differently was I took the door off for an easier reach. To take the door off, you open just a little and pull up. It makes it so much easier to get at the screws, and maked the repair a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Alice, TX
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned out heating element
took 5 minutes with a nut driver and son. I had previously watch your video and went exactly as the video described and showed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Chicopee, MA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bake Element burnt out
watched the video on part select - took less time then they said.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emily from Snoqualmie Pass, WA
- Parts Used:
- WB30X46986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broiler Element Replacement
There were two small screws at the back of the stove (this was the part that intimidated me. At first glance it doesn't look like it should be removed). But you just have to unscrew them, disconnect the wires behind them (this part can be done by hand), and pull the element out. The new element slides right in! Just make sure the power to the stove is disconnected either by breaker or by unplugging it. I'm not sure if it matters, but I made sure to connect the wires to the same side of the element that they were removed from.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stuart from Yelm, WA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element not working
Saw the brief video and as stated took less than five minutes to replace. It took longer to clean up the floor under the oven than to replace heating element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from morton, WA
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burned out
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jenny from Muskego, WI
- Parts Used:
- WB35X29720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Replace oven gasket
I used the pliers to remove the old pins, and popped then new pins in place...super simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from PARIS, MI
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the bottom element of the oven was broken
attached the element,pushed it back in the pocket,put the plate back on, screwed the nut and bolt back on and was done in less than 4 minutes!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Granby, CT
- Parts Used:
- WB02K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic glide broke
The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Rock Falls, IL
- Parts Used:
- WB30X46987
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
lower burner quit working.
easy, less then 15 min. but take off door first makes alot easier. and don't forget to unplug, like i did. just a few sparks but no damage thank god.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Ellenboro, NC
- Parts Used:
- WB24T10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The 8" burner switch heated burner to high Temp
Went online looked up model no and found Part No. and ordered it couple of days It came in mail Cut power to oven took knob off two screws back panel. wired new switch like the old one replced thwe switch and two screws and panel connected the power tried new switch it worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from Selma, AL
- Parts Used:
- WB35X29720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The oven door gasket was worn and didn't provide a good seal.
I use needle nose pliers to remove the old gasket tabs and clean the area with a scouring pad. Then I just lined the gasket up with the holes on the door and pushed the holding tab into the holds.Very easy and simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from protection, KS
- Parts Used:
- WB30X46987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
element burnt out
ordered part shut electricity off took out 2 screws took of connectors put in new element replaced connectors replaced screws turn on elec started cooking
Was this instruction helpful to you?
Thank you for voting!