JB258RM4SS General Electric Range - Instructions

This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.

Took out the old & put in the new one-Done!

I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

Followed directions given by previous customers problems which we found on the internet.

Top front sloping sheet metal panel with all controls and plastic end caps has to come off. Need 2 people, one to hold it while other replaces switch. Problem was getting screw holes on bottom ends lined up and cuts from sheet metal edges. Ten minutes to get it apart, 40 to get it back together. New switch works fine.

Mice took over trailer, after eliminating mice, and cleaning oven and range thoroughly, I noticed that the only place the mouse urine smell was still coming from was the vent tube. Noticed soiling around tube where it went through and into oven. I removed the center rack, layed some foil to catch any debris that may fall from the tube when it is removed. I removed old vent tube simply by removing the two nut screws on the roof of the oven. I had to pry it out a little bit. I then cut out and soiled insulation with razor knife, I inserted the new vent tube from the inside, and replace 1/4 nut screws and tighten.

Removed two screws holding the housing in place and loosened two more on the back it order to free it. Switch was held i place with two screws, removed those. Transfered wires one by one on the new switch, which was identical OEM part, and replaced the screws. VERY simple.

Remove oven light lens cover, remove the bulb and replace it with a new one.

Thank goodness for PartSelect.com
When we moved into our home the microwave and electric range are obsolete appliances and were missing parts. PartSelect.com has pictures of parts on one inch grid pattern so I was able to select the hard to find parts that would fit perfectly and they did.

As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

It was easy to just replace the old burner bowls rather than try to clean them. The peices ordered from Parts Select were a perfect match and they arrived on a timely basis.

Just removed the old drip pans and then inserted new ones...pretty dog gone easy!

replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!