PB935BP3TS General Electric Range - Instructions

After opening the Oven door, I removed the glass cover to view and locate the bulb, at the inside, top front of the Oven. Removed the burnt out bulb by pulling it in a forward motion towards the front of the Oven, slid the new bulb into place and the Oven is again functional.

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

Pull oven away from the wall. Unplug from 220VAC outlet. Remove six (6) black screws from the upper back panel. Remove two (2) screws and washers from top of upper back panel. Rotate panel down and pull away from the back.

Remove burner control knob. Remove two (2) screws from burner control. Pull burner control backward through the open back. Disconnect upper and lower cable bundles.

Connect lower and upper cable bundles. Push control knob post through the front on the range. Install two (2) screws to hold the burner control. Install burner control knob and turn to the off position.

Reinstall upper back panel. Secure with two (2) silver screws with washers. Install six (6) black screws.

Plug in range 220VAC cable. Slide oven back into place.

Tested burner on high small burner, low small burner, high large burner, low large burner. All tested fine, burner cycled on/off cycles as expected.

Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.

Pulled the range away from the wall. Took two screws off of top cover with 1/8th socket wrench. Took small Philips head screw off the top, just leaned the cover away from the top. It still held in slots at its bottom so no need to drop it away from the range. Removed the dial from the front exposing two small Philips head screws. Removed screws, and pulled the comptroller away from the rear of the range. Held the new one in the same position as the old one and removed one connection at a time, and replaced them into the new part. Did everything in reverse to put it all back together. Believe me, easy as could be and you just saved $200 repair man cost. Part matched old part exactly.

I viewed the video available through part-select. The most important thing I learned to do was to change one wire at a time instead of removing the old switch completely and then installing the new one. With 5 wires involved, it was really simple to install and not have to remember which wire went where. I was surprised how easy it was and it works wonderfully!

unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$

I pulled the stove out, unplugged it, screwed off the top back panel, held the control switches side by side and switched wires out one at a time. Put everything back together and pushed the stove back. Everything works like a charm. I’m a 60 year old female and that job took me 20 minutes start to finish-easy peasey.

I changed out the sensor and still same problem. Change out Thermosat and still same problem.
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644

Cut all power to the range. Easy to remove front panel and then screws and nuts that hold both white frame and glass top to range. Once the top can be lifted, cut the plastic zip tie that retains the harness. Unplug the harness and then remove the top. make provision for new zip tie before
the range top is re-installed. The range top is to be inverted for installing clips to the new heating element. Make sure that the holes line up to the pointed clips that hold the element. Not required to move the range.

This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the connector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.

I just followed the instructions on the link provided with the part

Replaced infinity switch: unplugged stove;. Removed upper back panel (4 small screws using socket wrench. Appropriate size box wrench would be fine, too); pulled off burner control dial. Removed 2 small screws with phillips screwdriver. From back of stove noted position of infinity switch . Replaced wires, 1 at a time, onto new switch. Pushed new switch
into same position as old switch. Secured with the previously removed screws. Replaced the control dial. Replaced upper back panel of stove.

Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

Remove cover on back remove two screws for switch and take picture of wire placement install new switch put all back together
U. Plug stove first . Was really easy to do now have room do a other burner