JM250DT1WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert W from Whitehall, PA
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner went to high heat at any setting
Thanks to Partselect's instructions the repair went very easy. When I was done and the wife finished cleaning the sides of the stove and the floor behind it, I was surprised after I plugged the stove back in and noticed the clock was only 18 minutes off! Awesome company to deal with, Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from N. Fort Myers, FL
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed "original style" on older stove
I needed to replace all stovetop bowls and found all after-market bowls "just a little off" effecting how flat the burner rested so called PartSelect's hotline and was assured that if I were using the actual model number found on the stove the parts would definitely fit and not almost fit, guaranteed, and they did!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Renton, WA
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Found out Drip Bowls can not be added to self-clean
Dropped in new bowls. I was surprised how in-expensive new ones were.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from ft.pierce, FL
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rusted out burnner bolws
Remove old burnner bolws and install new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda L from Lake Placid, FL
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My drip bowls were rusted and corroded
I ordered new drip bowls and put them in place. They fit just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Connice from Massena, NY
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new drip pans-
replaced pans- what I would like to comment on is the time- I ordered one day at noon and had them the next day at noon- I live in tiny town on northern border of USA- it was awesome- I couldn't believe it was them- 24 hours- super job and excellent price too
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from Hill, NH
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip Bowels badly stained.
Unplug heating elements and pick up drip bowels and reinstall elements.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Prosser, WA
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Burner Switch Went Out
Turn off power at main electric panel/ move stove away from wall and unplug cord from outlet. Take knob off the front take two screws off the panel, take back panel off and remove the used switch and take and replace the wiring to the new one , one at a time wire for wire. Then put back tighter in reverse of the way you took it off. Plug in cord and move stove back to the wall. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- julio from hobbs, NM
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
surface burner would not work
watched it on parts select this is a real fast and simple install took longer to pull the range out of its position well started by shuting off the power then double checked that the range was deenergized removed the knob then the 2 screws then on the rear of the range removed the back panel about 8 screws used a nut driver then removed the old switch removed each wire one by one and pluged each wire into the new switch just as they were on the old switch the new switch was exactly the same so every thing matched up perfect installed the screws to the front which hold the swich in place then the back cover turned on the power and tested the switch every thing working ok done shut off power slid range back into its place turned power back on everything still ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sunny from Salt Lake City, UT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
stained drip bowls
unplugged burners replaced drip bowls plugged in burners
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Apache Junction, AZ
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old,burned pans
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from Dallas, TX
- Parts Used:
- WB48T10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing racks
took the old ones out and put the new ones in their slots. No issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GAIL from STREAMWOOD, IL
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new drip pans
Not really a repair. But would like to say, I like the price and shipping was super fast. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sandstone, MN
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
uneven heating of oven
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Leon, KS
- Parts Used:
- WB17T10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Burner wouldnt heat
Watched video,and used it as guideline.Biggest problem was removing tape from old wires.
Was this instruction helpful to you?
Thank you for voting!