JB655DK8WW General Electric Range - Instructions

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

YouTube to review, had 1 person hold stove top for ease. Simple repair

Really easy repair, two bolts on the inside of the oven door release the handle assembly, and four more bolts, two on each side, to release the handle from the frame. Then slide the glass into the placeholders and reverse install.

Easy install, clean all fastener locations.

Unscrewed the stove top and replaced the element.

The burner remained on high regardless of the position of the control. 1. Unplug the range. 2. From the back of the range control panel, remove the top-plate that covers the controls. (4 screws) 3. Remove the two screws that hold the control knob in place. 4. Move ONE WIRE AT A TIME from the old control knob to the new gripping the connector only (do NOT pull the wire). 5. Remount the controller and reassemble the back cover with four screws. 6. reconnect the range and test.

Remove 2 screws and 2 wires- took the coil, then installed the wires and put the screws in--works fine. Thanks for the fast service.

Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!

Watched youtube video. Very easy to replace

Ordered the part. Received the box damaged and did not realize the part was damaged until our son came all the way from Columbus Ohio to install it. We ordered another part which came in a timely manner. Even though I reported the problem and told them that we are not very computer literate they still would not accept that the part was damaged until we sent a picture. Our son came back from Columbus to install the new part which took about an hour. He took pictures which I was then able to send. They then asked for a serial number. I had already sent all the numbers from the part but that is when they said they wanted the serial number from the stove. We are elderly and getting that required me getting on my hands and knees to get it near the floor. Luckily I was able to get up. After multiple emails I now have to send the part back. Good luck to anyone working with this company. I will be waiting for them to reimburse me for the defective part.

Performed repair using a video for reference.

threw out the old ones and slide in the replacement ones from you.

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

recieved part the next day. looked different but I followed instructions and the part worked perfect.

First I removed the oven drawer. Verified that the support clips would rest correctly on rail, then review installation document with supports to locate alternate location for replacement supports. I did have to personally locate 2 fastners not provided with the supports ot complete installation. After installation, oven drawer opens and closes smoothly.