JMP28GV1AD General Electric Range - Instructions

just plugged it into the socket

Removed the old and slipped in the new.No problem and it works fine.

Installation took 30 seconds. Your website was easy to use & the part received was just as described. It arrived beautifully wrapped & in just a few days. ABSOLUTELY AWESOME!I will recommend your site to everyone.

I pulled out the heating coil and pushed in the new coil. I turned the stove top on and heard a sound like "dzzzt". I immediately turned off the burner and waited for it to cool, then pulled it out. The part had a burn melt on one side of the end prong. It turns out that the part that the burner plugs into needs to be replaced. Actually, the stove top is over 20 years old and my landlord will have to replace the whole unit. So it turns out that I didn't need to order a surface element after all, but it was very easy to install!

ordered new surface element and pushed in to conector turned on switch to test and works fine thanks

Just put it right into the receptacle. I want to add...we had gone to our local appliance store and brought home a wrong-size unit. Got online and your website came up. It was easy to find the correct part, ordered it and it arrived 3 days later. I have already recommended your website to 2 of my friends. One very good experience!!!

I simply pushed the new burner into hardware. I then tested it to see if it works. . .

Turned off power. Removed two screws. Took out old element. Used pliers to remove connectors. Installed new element. Set screws. Turned on power. Works.

ordered parts and disassembled old burners and installed new ones. All the parts were in the box when delivered.
Helping my 80 yr old mother-in-law very happy.

Got parts in for one of her 81st birthday present she was thrilled.

I've been looking for an 8" replacement burner for my GE stove after my original burner caught on fire over a year ago. I had all but given up on finding a replacement after searching at all the stores in my area and also searching on the net. After cooking sides for Thanksgiving dinner this year and the pain of cooking with only 1 large burner, I decided to search again for a burner on line and thank goodness I found this site! All I did was put in the model number of my range/stove and the site directed me to the replacement burner. The picture of the burner looked like mine, so I decided to purchase it but I still wasn't convinced it would fit and work because of my failed previous burner purchases. I really thought my burner was too old and the part was no longer made. Well the part shipped very quickly and lo and behold it fit and worked! Installing was a breeze...I just snapped it in...thanks so much!

This the second time in three years the end caps broke. The first time the replacement end caps slid right on but, this time it was an extreemly tight fit. I had to sprsy white greese on the handle bar and inside the end cap and, even then I thought the end caps would break it was so hard to get on.

Repair was basically simple. Remove 6 screws holding door facing on door, remove one screw holding handle end caps in place. Then reverse the operation installing handle end caps. The problem I had was that the new a end caps had different dimensions than the old ones and the handle wouldn't slip into them. Had to carve away material inside the new caps with an exacto knife in order to fit the handle. The result was a 15 minute job took well over an hour

First I made sure I turned off the breakers in the circuit box that controlled the circuits for the ovens . Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The factory wrapped a large amount of tape around the connection between the wires and the heating element. That took a while to get off. And I searched for heat-resistant electric tape to replace it (because, it must have served some purpose if they had it on originally). The wires hooked onto the spade connectors for the new elements with no problem. I pushed them back into the hole in the back of the oven, replaced the screws, turned the breakers back on, and it worked great from there on.

Dislodged screws to oven door to get to handle assembly. Fairly easy, however, new door handle end caps do not come with screws and the old screws were not a good fit. Almost stripped the old screw trying to get it in place. Strongly suggest that Part Select send replacement screws with handle to facilitate repair. Door handle is back up but is now loose until I can find/secure appropriate replacement screws and repeat the process all over again.

After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.