JBP30WA3 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Nashville, AR
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
R had ight front control made loud noise when contacts opened.
This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Ferndale, WA
- Parts Used:
- WB27X10311
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
Oven Bake element did not work
After needlessly replacing the Thermo-sensor and Bake element I was able to determine that, while I had proper voltage to the appliance I did not have power to bake element when bake knob was turned on. The broil element worked properly. I hesitated purchasing the Electronic Clock Control because there was nothing wrong with the oven clock and it was an expensive part. I switched out the control unit and was delighted to see the bake element heat up immediately. It was simple to replace and the instructions that came with it were adequate - just some differences in the color of wires. Thank you Part Select.com!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Walton, KY
- Parts Used:
- WB44X10016
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
oven element burnt up,was throwing sparks...
took the two bolts out of element, pulled the wires and replaced...It was the fast shipping and receiving that made it awsome.. was all done in 2 days..thanx
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Redding, CA
- Parts Used:
- WB23X5340
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
oven continued to get F2, F3 and F5 error messages when ovewn got hot
This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a support bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Montgomery,, AL
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
welded supports for the surface elements were broken
unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DeeAnn from Clinton, MO
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob had broken off
My husband was able to easily remove and replace the switch and know with-in 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rod from Huron, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leonard from Winter, WI
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Floyd from Warren, OR
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Linthicum, MD
- Parts Used:
- WB27X10311
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inconsistant oven heating. I tested the sensor and it checked good at room temperature. When I tested it in boiling water and ice water the resistance read lower than it should have. I concluded that thevsensor was the problem. I replaced the sensor but it did not solve the proble. I therefore,
The repair was quite simple. I pulled the range away from the wall. Removved 6 screws from the back panel with a nut driver. I the disconnected the wires from the clock control and then removed the 4 screws securing the control board. I loosened the faceplate from the old control with a hair dryer and removed it with a knife. I afixed the faceplate to the new control with two sided tape. Connected the wires to the new control and secured it with the 4 screws. The only problem one might have is the instructions referenced black and purple wires whereas mine were red and blue respectively. Reattached the back panel with the six screws and plugged the power plug back in. Moved the range back against the wall and tested the oven which tested perfectly. Note please disconnect power before proceeding with the installation of the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Fort Myers, FL
- Parts Used:
- WB07K10043
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Right Oven Door Handle End Cap Broke Off
Went on line and watched a couple of instr. videos which were very well done and explained just how to replace the end cap. I purchased and relaced both end caps and was able to clean the entire handle before putting it all together. Looks really good now. Thankyou. JJM
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudine from The Colony, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
surface element not working
I simply pulled the old surface burner out, and plugged the new one in. It took less than one minute! The amazing part of this repair, is actually that PartSelect sent the replacement surface element burner OVERNIGHT! I could not believe it, and was VERY impressed with their commitment to help their customers in time of crisis. It arrived just on time for my Thanksgiving not to become a nightmare. Thank you PartSeclect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from El Paso, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element would not heat to red hot.
unplugged and installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jilan from South Milwaukee, WI
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scorched Element
It wasn't so much the repair that was needed as how impressed I was with the fast delivery. Without a fourth burner & a holiday weekend coming up I was in desperate need of my element. I ordered it around 1:00 pm on a friday & it was delivered the next day before noon! Very impressed with the ease of ordering & receiving. Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Copperas Cove, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No Problems
I removes the old element and drip bowl, then replaced the drip bowl, then replaced with the new element. Approximatly 3 minutes. . .
Was this instruction helpful to you?
Thank you for voting!