MB757WB1 General Electric Range - Instructions

Simply slide stove away from wall and unplug. Remove the center back plate on the rear of the stove, Open oven slide new element into rear of oven, snap into place. Return to rear of oven. slide wire connectors onto oven element prongs, replace center cover, make sure oven is turned off, plug stove back in and slide back into place. Open oven and turn on. allow element to heat up. Once the element has heated and the new burns off. Turn off the oven and replace the racks, This entire process took maybe 5 minutes.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Shut off power at the panel to the electric oven. Removed 2 phillips screws holding bulb unit in place in the top of teh oven chamber. One wire was so frayed it came out of the push on connector. Stripped off insulation and reinstalled onto the connector, using pliers to snug the wires down. Installed the new porcelain socket from Parts Select, replaced the unit in the top of the oven unit. Installed a new bulb, then snapped the new glass housing into place with the existing retaining wire clip. Presto: works like it's brand new. Thanks to Parts Select for the right parts, and for such quick delivery. I will use them again!

Took the upper back covering off, disconnected the clock control. The only problem is the replacement didn't have the same connections so I was able to pull up the replacement number of wb27x10311 and asked for a diagram which told me exactly where to plug each of the red, white, blue and yellow wires, what a relief! To my amazement I fixed my "old" stove for less than $160, if I had called GE to service it, I'm sure I would have been looking at a $400 bill. This was the way to go, Thank You!

After needlessly replacing the Thermo-sensor and Bake element I was able to determine that, while I had proper voltage to the appliance I did not have power to bake element when bake knob was turned on. The broil element worked properly. I hesitated purchasing the Electronic Clock Control because there was nothing wrong with the oven clock and it was an expensive part. I switched out the control unit and was delighted to see the bake element heat up immediately. It was simple to replace and the instructions that came with it were adequate - just some differences in the color of wires. Thank you Part Select.com!

I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

Good directions

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

The only problem was m short arm and no good flash lights around

Remove center cover on back of stove exposing wiring. Unplug stove from 220v outlet. Unplug wires from old element.From inside stove, Remove 4,quarter inch screws holding back panel inside oven in place. Remove back panel from inside oven. Will be able to see the brackett on element and 2 screws holding the element/brackett in place, remove those 2 screws and remove old element. Reverse process to install new element.