JCBP68SM1SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- B from Niceville, FL
- Parts Used:
- WB44T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Gizmo in oven that gets red hot when you bake had burned out.
Gizmo = Bake Element held in place with 2 bolts inside of oven. Removing them only difficult because they are so deep in oven. I did not have the correct size nut driver so I started with my socket wrench then switched to putting the correct size socket on the end of a long screwdriver. After removing the 2 bolts fund element did not slide out easily so went to back of stove and removed a metal protective cover. Found electrical lines secured to the ends of the element. Had someone hold element while I pulled each of the 2 loose - at which time bake element fell loose. Put new one in by reversing the process. That night wife set stove to Clean - and said best it has been cleaned in years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Knob Noster, MO
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken rear drawer support
Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dock from Aurora, CO
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The storage drawer came without supports.
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent J Paola, from GREENWEL SPGS, LA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bad Line fault displayed on range clock
1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from LONGS, SC
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven door gasket needed replaced
Ordered the part, it arrived and 5 minutes later it a complete installation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEAN-C. from PARRISH, FL
- Parts Used:
- WB44T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven wouldn't heat
removed two screws that hold the element in place and then removed the access rear panel it was much easier to disconnect the element than have to stick my head in the oven to gain access.time :15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from TICKFAW, LA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Oven board went out
One wire at at time then used my razor blade to get front off stuck right back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from GOLDSBORO, NC
- Parts Used:
- WB44T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
bake element burnt out
unscrew and disconnect the old unit. Connect and screw in the new unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from shandon, CA
- Parts Used:
- WB44T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
element burned apart
pulled range out,unplugged it,thenI removed the two screws that hold the element in place.take back cover off, then pulled the element out about 3 inches and disconnected the two wires.put new element in,put wires and screws back in place,checked to see if worked,did not work,check and reset breaker,it works put cover back on,push range in palce and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NICK from Vernon, CA
- Parts Used:
- WB48T10068
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Plastic guide Broken
replaced Plastic Guides
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heinz from Colleyville, TX
- Parts Used:
- WB44T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Lower heating element broke and burst in flames
On the website, the heating element looked exactly the same with same measurements as the old one. However, the part I received did not match. The screw holes where the element attaches to the back were wider apart and higher. Plus, the leads curved up instead of being straight.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Canterbury, CT
- Parts Used:
- WB44T10011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven heater coil burned out
Removed power plug- disconnected wire, removed cover over wires two screws, and removed old heated strip, held in by two screws inside of oven
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Saint Johns, AZ
- Parts Used:
- WB03T10281
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Knob part broke on & off switch.Got a nee
Got a new knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Ogden, UT
- Parts Used:
- WB44T10011
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
oven wouldn't heat
My friend's husband came over to help. I mentioned that after unscrewing the old bake assembly unit, we would have to capture the wires or they would slip into the back. Before he even had the screws undone, the wires did, indeed, slip into the back. He then removed the back panel and retrieved the wires, pushed them back through the insulation and clipped each of them onto the back assembly. However, the wire clips kept slipping off so he eventually had to criimp the clips to keep them tight on the ends of the bake assembly. That troubled me; what if in the future one of those clips comes loose while the oven is in use? Any suggestions on how to keep these connectors on tightly?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from Cromwell, CT
- Parts Used:
- WB44T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom element fell apart
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. ordered the part and connected the element back to the two wires replaced the two screws plugged in the stove turned on the oven and we were back in business,
Was this instruction helpful to you?
Thank you for voting!