JGBS80DEM1BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juanita from GAINESVILLE, GA
- Parts Used:
- WB16K10070, WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
gas burners not heating evenly
remove old burner, put new in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Ashland, MA
- Parts Used:
- WB29K10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn and pitted burner caps
Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- P from FULLERTON, CA
- Parts Used:
- WB13X26360
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Part does not look like the part that needs to be replaced
I have no clue what wire goes where because there is no thing to refer to or instructions of any kind . I have not been able to install the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Long Beach, NY
- Parts Used:
- WB13K10014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
To Replace Gas And Burner Parts In Section 4
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Dexter, GA
- Parts Used:
- WB27K10356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven stays in Preheat mode
first i changed out the temperature sensor that was bad did a ohms check on the old sensor an it showed OL on my meter, after installing new sensor then got a F4 code on display pad changed TO9 Control and that fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from West Chester, OH
- Parts Used:
- WB62K10110
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
BLK top stained and chipped
upon disassembly broke gas feed to front burnner. After recieving new feed tube and seeing to remove center nut around the orfice all went well. to disassemble remove all 5 nuts around burnner orfice then top can be removed with spark igniters. all the rest is easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Monterey, TN
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from Nashville, TN
- Parts Used:
- WB13K10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Large burner wasn't lighting very quickly
Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Watervliet, NY
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Forgot to remove the heat shield from the old part.
Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Somerset, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven liner melted....needed to replace bottom
Removed the old oven bottom by removing two nuts. Be careful...don't drop the nuts! Removed the heat shield that was attached with four nuts to the old bottom and transferred it to the new oven bottom. Then placed the new bottom in the oven and secured it with the two original nuts. Easy...but don't forget about transferring the heat shield and don't lose the nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from CYPRESS, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from SAHUARITA, AZ
- Parts Used:
- WB32K10036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven door gasket tore
Slid the oven door off of the hinges and laid it on a sheet on the kitchen island counter top. By simply looking at the spring clips on the new door gasket it was obvious how to use pliers to squeeze the clips on the broken gasket to easily remove it. I took the opportunity to clean the oven door before putting the new gasket on. Installing the new gasket was very easy, simply inserted the spring clips into the holes on the door and pushed until I heard the "click". Anyone can do this repair.
Was this instruction helpful to you?
Thank you for voting!