JBP30WXB1WW General Electric Range - Instructions

Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.

ordered over the phone a new temp sensor. Un plug the oven, take off the back, open oven and unscrew the temp sensor, pull the sensor until the elec connector clip comes through so you can unclip the old sensor, clip on the new then pull the line back and re attach the sensor to the ovn. Plug in the oven.
Pretty simple, just hard to work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.

First I searched for the part here and I had a slightly hard time finding the correct element on the site.
Then I read the comments of the others and the issues they faced.
I unplugged the range and pulled it out a bit from the wall. I then removed the two screws that hold the element in place and put them where I would not lose them. Then I gently maneuved the element out and placed a clothespin on each of the wires to keep them from going back in and then disconnected the wires from the element using a pair of needlenose pliers.

At this point I had to gently bend the new element back into shape as it had been bent during shipping. Then I connected the wires and slid the element into place and installed the two screws.

Double checked to make sure everything was ok plugged in the range, said a quick prayer and set the temperature to 300. When it got to 300 the element shut off and I was happy that the element did not take any other parts with it.

First I removed the five screws that hold the
element in place and pulled the element out
about 3 inches and disconnected the two wires
and hooked a piece of wire on the leads to make sure they did not fall behind the cabinet.
Then I connected the new element to the lead
wires and removed the piece of wire and secured the new element in place with the mounting screws. Took about 25 minutes to remove and replace.

Replaced element control switches

The parts were shipped quickly and were what I ordered. The one suggestion I would make to the installer would be to drill out the insert holes a bit in the plastic columns in the inside of the bracket. There are two such columns and they are used to provide further strength to the end cap. However, the diameter of the screw is too large for the insert hole because as I installed the first bracket one of these columns broke. After drilling out the insert hole, the screws were still snug and the end cap (and door handle) was quite solid.

couldn't get exact fit--out of production. mounting bracket at back of range for new element too small. took bracket off old element. cut down bracket on new element with tin snips, drilled holes thru it and old bracket and screwed together. at this point the new element was to long & touched oven door. removed spacers that came with new element (used old support to attached to roof of oven) and pried elements apart (which made element wider & shorter). working good.

replaced lights in refrigirator and freezer

It took my son very little time to install control switch. Using a screw driver he removed the back panel directly behind burner units & replaced the control switch. Very easy.

Removed torx head screws. Removed broken pieces of the end caps. Replaced the handle installed the end cap screws.

I just inserted the replacement where the old one had been connected. It took less than 5 minutes. It was so simple & easy that 'repair' is too generous a word -- & I am NOT handy, in any sense of the word. It took me longer to figure out where to find the model number!

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .

I just follow Steve's Installation Vidio. My range works.
Thanks Steve