JB625DK6BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from LONGS, SC
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven door gasket needed replaced
Ordered the part, it arrived and 5 minutes later it a complete installation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from JACKSON, MO
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
control switch had stopped working, burner wouldn't work properly
took out a couple of screws and replaced with new switch, plugged in switch wires. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from SAINT PAUL, MN
- Parts Used:
- WB02X38986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacing handle spacer
This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from Portland, TN
- Parts Used:
- WB24T10029
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Element blew hole in self then no power to burner.
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Minnie from hurdle mills, NC
- Parts Used:
- WB07X42966
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
just want new parts
very easy and clean.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from N CHESTERFLD, VA
- Parts Used:
- WB14X41386
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Oven door wouldn't close properly
Watched video on you tube. Removing/reinstalling all of the screws/bolts took longer than the actual repair.. Took 23 minutes total from turning power off, repairing and turning back on. Super easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from TICKFAW, LA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Oven board went out
One wire at at time then used my razor blade to get front off stuck right back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SAN TAN VLY, AZ
- Parts Used:
- WB21X22134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not Reaching Temperature above 300 Degrees
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from CLAWSON, MI
- Parts Used:
- WB44X45494
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element was burned out.
unscrewed element from back of oven disconnected power source. Replaced new element & screwed new wires onto back of oven. Took 5 mins. Works like new. I am 73 yr old female so anyone can do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from JACKSONVILLE, FL
- Parts Used:
- WB04T10086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced oven door gasket
Remove old stained gasket and replaced with new. Only $57.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from WEBSTER, TX
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from COHOES, NY
- Parts Used:
- WB27X45466
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Bake button stopped registering
This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caitlin from MOUNT SHASTA, CA
- Parts Used:
- WB14X41386
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Handle would not pull the latch back any longer
Super easy repair! There are videos online if you have one type of oven, I had the other type (with the little silver plate right above the latch part). The trick is to remove the handle from the assembly itself before removing or placing it in the oven. 4 screws total and I recommend needle nose pliers to help remove the wires.
Was this instruction helpful to you?
Thank you for voting!