XB625RK5SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Curt from Maple Grove, MN
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner light would not shut off
Checked each burner switch by disconnecting the light indicator wire. Located the switch, replaced the switch and the indicator light operated as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Brandenburg, KY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Prosser, WA
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Burner Switch Went Out
Turn off power at main electric panel/ move stove away from wall and unplug cord from outlet. Take knob off the front take two screws off the panel, take back panel off and remove the used switch and take and replace the wiring to the new one , one at a time wire for wire. Then put back tighter in reverse of the way you took it off. Plug in cord and move stove back to the wall. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- julio from hobbs, NM
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
surface burner would not work
watched it on parts select this is a real fast and simple install took longer to pull the range out of its position well started by shuting off the power then double checked that the range was deenergized removed the knob then the 2 screws then on the rear of the range removed the back panel about 8 screws used a nut driver then removed the old switch removed each wire one by one and pluged each wire into the new switch just as they were on the old switch the new switch was exactly the same so every thing matched up perfect installed the screws to the front which hold the swich in place then the back cover turned on the power and tested the switch every thing working ok done shut off power slid range back into its place turned power back on everything still ok
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lynn from sunnyside, NY
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
F2 reading
Followed the instructions that were sent to me by E-Mail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from gap, PA
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
f-2 or f-3
remove two bolts in on sensor and slip thru back un plug and reverse to put in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Sonoita, AZ
- Parts Used:
- WB27T10668
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Pilot light out
Removed the power plug from the wall, screwdriver and small socket allowed me to remove the front control panel. Once I located the pilot light I pulled off the holding clips and placed a new light into the holding clips...problem solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEE from ROME, GA
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Large eye would over heat when was on med. settings
I unpluged the stove pulled it out and took the 6 screws off the back to get to the switch. Around front take knob off and removed the two screws holding the swich in place and pulled it out the back. Pulled one wire at a time off of the old switch and replace on the new switch. Nothing to it had it done in just a few mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Winter Garden, FL
- Parts Used:
- WB24T10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner would not turn off
The burner light did not turn off, and the rear burner stayed hot. Unplugged unit and removed switch, which turned off the "burner lit" lamp. Thus I figured it was the switch that was causing the problem. Ordered the switch (I think around $18 and plugged it in. I think there were 4 screws to get the panel off, and then another 2 to get the switch off. When I plugged the unit back in (it had been unplugged while I waited for the part to ship) it beeped for a while. I had to turn the breaker on and off, and that solved the beeping problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Ellenboro, NC
- Parts Used:
- WB24T10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The 8" burner switch heated burner to high Temp
Went online looked up model no and found Part No. and ordered it couple of days It came in mail Cut power to oven took knob off two screws back panel. wired new switch like the old one replced thwe switch and two screws and panel connected the power tried new switch it worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brendan from lebanon, NH
- Parts Used:
- WB17T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DONNA from EAST MEADOW, NY
- Parts Used:
- WB30T10136
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
8 Inch Burner Inop.
Remove range top [ten phillips screws] remove electrical connectors and lift out burner. Reverse procedure for installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felipe from Donna, TX
- Parts Used:
- WB24T10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The burner combusted burning the the burner switch
Disconnected the appliacnce from the power source. Using screwdriver, removed the back panel and disconnected every wire that are connected to the switch. Pulled out the front nob and removed the switch. Then install the new switch by screwing it back in. Place all wires back and back panel. Connect and finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lisle, IL
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven not warming, f2 indicating overheat
Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!