JGBS61RP1SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Donald from Millville, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not light.
First I took off the oven door which was a snap. Then I removed the bottom drawer. I removed the i guess you would call it the spill pan which was two screws. removed the guard plate and disconnect the igniter and remove the two screws that was holding it in place. Peace of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Auburndale, FL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
temp in oven not constant big swing in temp
removed oven door racks and pan from bottom of oven. removed warming drawer unplugged oven igniter removed 2 hex screws from bracket on igniter. replaced with new one fiched wire down to warming drawer area plugged in. replaced door and warming drawer. works fine now. very ez to do!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Crawfordville, FL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Oven wouldn't light
Replaced the igniter. Quite simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Alger, MI
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not start.
Bake ignitor would not glow. Removed racks and lower pan to access the ignitor. Removed two attaching screws and unplugged electrical connector. Installed new ignitor. Hint: Gas will not flow unless both the bake and broil ignitors are operational. Ignitors are interchangable; you can test ignitors by swapping them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Palmdale, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
intermittently would heat - extremely random - 2 year
replaced the ignitor and it has worked perfectly the last week - Service repair walked away from the service call stating it was too random - you website state 91% cause, you were correct I wish I had done this 2 years ago
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from WHITEHOUSE STATION, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven would not heat
igniter was not glowing bright...removed old one and installed new one all within 30 mins.Part was exactly as description and picture really helped. Turkey for Thanksgiving will be served cooked by my oven.Thanks.. Daniel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- grady from Brooklyn, NY
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven did not work
Remove the warming drawer to get to the electrical connection, Remove two nuts from igniter, replace igniter fasten the nuts and connect electrical. Oven works fine. BEST PART OF THIS......SAVED $250.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Northlake, IL
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Igniter would glow but the oven won't turn on
Just replaced the igniter and it works fine now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Devin from Colorado Springs, CO
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
no ignition in stove
replaced the glow bar ignitor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from North Smithfield, RI
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
oven wouldn't light
removed bottom drawer, disconnected screws holding burner in place. unplug igniter. remove bottom tray from inside oven, remove 1 screw holding burner in place near door, remove whole burner assembly. take 2 screws holding element in place. screw new element to burner and reverse procedure. only tool i used was a 1/4 in nut driver.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Pacifica, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
wife complained that oven was not maintaing proper temp
Researched problem came to conclusion that igniter was not staying hot (seemed to intermittently go on and off ). One connector and two screws problem solved and the cherry pies are back in my oven and ready for dessert! : )
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas from lindenwold, NJ
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
gas oven will not light, igniter is on...
replaced the igniter by first removing the pan inside the oven, two screws in the rear. Igniter is attached to the burner with two machine screws, nut driver or small wrench is needed. Remove the lower drawer and un-clip plasitc connection located in the rear up high. Pull the wire and clip through into oven. Replace with new inginater, pull wires and clip through the back of oven and tighten screws, plug clip in, replace pan and plug in oven, done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Orland, ME
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven igniter
Remove botton pan of the oven to get at the igniter, remove bottom drawer to acess wires ,remove 2- screws from the igniter replace then replace oven bottom and drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LaVerne from Republic, WA
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
oven would't light
removed the screws holding unit in pkce ,unplugged unit'Then I had to cut plug in off new unit and put old plug on new unit. the new unit only had 1 plug and the stove had a2 plug systtem. The put unit back in by replacing thw screws.
Was this instruction helpful to you?
Thank you for voting!