JB900KK2CC General Electric Range - Instructions

First, disconnect electrical power to the stove by turning the main fuse to the off position. Confirm that there is no electrical power in the stove. The ceramic top is held by 10 screws that are closest to the ceramic surface. Other screws hold other parts of the stove and not need to be touched when opening the stove. Once the ceramic surface is off there is access to the burners and the various lights and switches. It is important to determine whether it is the burner that is defective or the switch. Inasmuch as the switch has many moving parts, the switch is more likely to be the defective part. Check the switch by gaining access to the switch connections. There is a metal frame held by two screws on each side in the outside of the stove (same area where the initial 10 screws were removed to separate the ceramic surface). Remove these screws and flip the switch assembly so all the wires and cables are accessible. I checked the switch with a continuity tester and by trial and error determined that there were two connections that in all the remainder three switches had continuity when the switch was in the on position while the suspect switch did not. Replaced the suspect switch by pulling the wires and replacing them in identical positions in the new switch (a smartphone camera became very useful to remind me were exactly each cable's connection was). Restore power by turning the fuse to the on position. Check that the burner lights up. If not, change the burner as well. Same simple procedure of disconnecting and connecting cables to the burner). Make sure to disconnect power before working on the burner. Replace the screws that hold the switch assembly. Replace the ceramic top. Replace the screws. Set stove back in its hole. Reset fuse. Total time: 35 mins. Total cost: Approx $25.00 (switch + delivery). Quoted repair by local appliance repair service: $487.50. No contest. Next project is to fix a leaky water dispenser in the refrigerator.

1.Disconnect the power cord. 2.Remove two screws pull the element out. 3.Disconnect the wires attach to element. 4. Install the new element connecting the wires. 5. Align element with holes and tighten screws. 6. Plug in power cord and begin to cook.

Removed the rear panel from the Range using the nut driver. pulled the terminal wires off the back of the heating element. Double checked if there was continuity across the heating element terminals before removing the element. If there is none, its bad. remove the two screws inside the oven holding the element in place. Once free, lift the front of the element to about 30 degrees and pull towards you. Insert the new element in the reverse manner then secure it using the two screws. Push the terminal wires onto the terminals on the back of the element and reinstall the rear panel.

Pulled the old one off (very easy), used popsickle stick to push first end in slot, aligned pins, pushed them in the holes and pushed other end in the slot.

Opened the box removed old element with socket put new one in tightened and voila ?? Just in time for thanksgiving ??

We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

My son did it by using pliers. He took out the screws that held the element in and pulled it out and used the pliers to pull the wires out of the old one and snapped the new one in . put it back together. about 5 minutes.

opened oven door and removed two 1/4 " screws from range top. lifted range top and propped open like a car hood with a 1" diam dowel rod. marked on new element the wire color locations from old element and removed wires. removed the two small screws and clips that hold the element to the range top and removed element. Matched where the mounting screws locate to the new element. Installed new element in reverse order.

Removed old switch, put metal jumper from old switch to new one and connected wires to the new one . Reinstalled. Works great.

Turned off power. Opened range door, removed 2 screws that held top in place. Took a photo of the existing wiring for reference. Removed old burner. Be careful with spacers & springs. If dropped, they will be hard to locate in the insulation. Replaced wiring connectors & verified proper location with photo. Closed cover, replaced 2 screws & turned on circuit breaker.

Had to remove rear cover to connect wires, removing them from the front caused the wires to fall into rear.

This was a very simple procedure. I removed the 2 screws in the oven itself (holding the element in place), then pushed the element through the back of the oven so the wires were exposed, then slipped off the wires, the male end from the female end, I then removed the entire element. I put the new element in the over, re-attached the wires, put the screws back in place, replaced the cover, and the oven was as good as new.

I didn't know anything about this repair, other than I was replacing a part, so it never occurred to me that I needed to make sure there was no power to the oven. When I pulled the element out, there was a large spark. I flipped the breaker off, then finished the R&R.

Make sure you turn power off at the breaker, then replace the element.

Tim

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.