PB960EJ8ES General Electric Range - Instructions

Turn off breaker to stove. Remove 2 screws in front under stove top molding. Raise stove top from front on hinges in back. I used a piece of wood to support top up while I worked on burner. Remove screws holding old burner in place. I found my problem on the old burner - the outer element had been shorted and fried. Carefully remove each wire and reinstall in new burner in proper location. Reinstall burner and stove top with old screws.

had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yum.

The real challenge on this particular glass top range was to figure out which screws had to be removed to lift the glass top to get at the burner elements to do a replacement.

Removed the two side screws holding the control panel in place. Disconnected the two wire harnesses and took off the control panel to allow easier access. Then examined the screws attaching the vertical plate in front of the glass top. Most of them were on the on the vertical plate but a few were in the bottom of the horizontal plate. If successful, the vertical plate can be moved forward giving access to the glass top. You pull up on the front of the glass top and when it just clears the vertical front plate you pull the top forward a bit to get the back end of the top out of the read chrome vent piece. I then leaned the glass top up to about a 75 deg angle and then propped the top with a 24” wooden garden stake. I used two stakes to hold the top up. The challenge after that is to remove the old burner and carefully note the colored wiring and locations of the connectors and removed the three old clips. That took a bit of effort. several of the wiring harnesses were very short so you had to be careful when removing and installing the new burner. The burner has numbers stamped on the metal and you must note each number where the clips are located. The rest is to reverse the process. Some of the insulation pieces came off and some of the insulation clips fell off and you must be sure to get the insulation pieces back on in the correct location. Expect a lot of gunk that needs to be cleaned on the top and trim pieces. I save around $200 by doing my own replacement.

pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.

Disconnected the old socket ( 2 srews ) removed the two wires from the old socket, reconnected them to the new socket and reinstalled the lamp.

Watched video

First and most important trun off curcit breaker. Use 1/4 inch but driver to remove socket (2) screws. Remove ground and hot wire clips from old socket, replace on new socket. Screw back into oven ceiling and turn on power. Reset clock and your are done. Very simple.

First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches. I removed the sensor and disconnected the connector.

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

I checked various sites on the net and decided that the temperature sensor was the problem. The GE price for the replacement part was about $105, most of the other sites offered the sensor in the $70 range. PartSelect $12.95 When the part arrived, I removed a small self taping screw, pulled the high temperature wire connector into the oven space, disconnected the quick disconnect fitting, attached the new temperature sensor, pushed the connecting wire into its hole, replaced the screw and that was it. I probably saved about $200 in parts and labor over what a local repairman would have charged. Oh yes!! I first disconnected the power at the breaker box. Very important.

I have a double oven and coincidently I had to replace the two Oven Light Assemblies.
I am really glad about your web site because once I got the number from my oven model you guys were the first ones that came up. Thanks to your prompt and reliable service my oven is back to its original state.

Jose Figueroa

Sensor is in rear and on top ov oven. What could be a 10" job took 45". My problem was the oven door was diffinately in the way. Also I wear bifocals which makes me tilt head to see nuts. I felt like a contortionist. HINT: remove door and give yourself some room to work.

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

Unsrewed the glass cover

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.