JBS02 General Electric Range - Instructions

First I removed the oven door from the support hinges. Next I pulled the bottom pan drawer out to get to the tension spring. I released the tension from the hinge, unscrewed three screws that held the hinge in place. From there I replaced the hinge put all components back in place and did it all under 20 mins. The part was received with in 3 days from PartSelect so I was very satisisfied with the service and ease of repair.

Removed the oven door. Released spring on hinge. Removed 3 screws. Removed broken hinge and replaced new hinge reversing these steps.

Turned power off. Removed two screws holding the element. Pulled element out 3 inches, disconnected the two wires, pulled out old element, connected wires of new element, replaced screws. Turned power back on. Eureka!! the oven heats again. :-)

After removing the screws holding the element in I disconnected the wires and attached alligator clips to the wires to keep them from pulling back inside the holes. I would have had to pull the stove out and removed some covers if they disappeared through the holes. After getting the part number off of the old element, I ordered a new element from Partselect.com and received the new one in less the a week. Reinstalling the new element took about 5 minutes.

Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & since I was so tired from all of this 5-minute activity, I rested.

Al S.

After reading other stories, I knew enough to slide the lower drawer out and take off the spring. 30 second job. I did not realize that range doors slide vertically off the hinge, did that in about 2 mins. Put the new hinge on in 2 mins (3 Screws). Slid the door back on and done. Works like a champ. My wife has her eye on new stainless appliances. Sadly, she'll have to wait a while longer.

First I switched the fuse to the oven had no power and then I removed the old element and wiped down the inside with a damp towel.
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals and then done

Took out the hexagon screws, used pliers to pull the connecting ends apart, slid in the new element in to the connecting slots, reattached to screws, turned on the oven to see if it would heat up and it did. It was really easy. I had waited for a week to get the part from my local Sears parts house. You sent it out and I had it in 3 days. They still don't have the part. Thanks so much.

Uplugged the oven and undid the back contact cover, removed the nuts inside the oven and slid out the element. Pushed the new element into place and secured it. Attached the contacts and replaced the cover. Plugged it in and got cookin'.

I had grease on the baking element when I turned the oven on. I thought it would burn off, it caught fire and destroyed the baking element. I ordered a new element, it came within two days. I didn't wait for my husband to come home. I got a screw driver, took off the screw, used pliers to pull apart the old baking element from the wires. I did this carefully , our oven is old and the element was not pulling away easily. I inserted the new element, put the screws in and it worked perfectly! I was very proud of myself but the truth is that this is a simple job.

Pulled oven door up and off. Removed old hinge and installed new hinge. Replaced oven door. It was a very simple job. The whole project took less than 15 minutes.

removed nuts from inside, removed rear panel, pulled old
part out, slipped new part in.
DONE
SHIPPING AHEAD OF TIME, YOUR COMPANY SAVED ME THE PURCHASE
OF A NEW STOVE. THANK YOU FOR FAST & GOOD SERVICE.
NO ONE HAD THE PART BUT YOU FOLKS.

took out the old element after cutting the circuit breaker, put in the new one, it was that easy

What I had to do was open the slot for the burner pan more as it would not fit properly in. So we snip the burner pan a little and now it fits great.

orderd a replacement part. recieved it two days later then that evening installed it. there was a video online to show how to replace it. very useful if your not a do it yourselfer.