JMP28BA2AD General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Belle Plaine, MN
- Parts Used:
- WB64K5051
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Burn box had rusted through under one burner.
With a nut driver removed the four heating element sockets (four small sheet metal screws) and the seventeen sheet metal screws that secured the burn box, removed the sheet metal box and inserted the new one. Not all the holes lined up at first for the screws, but starting in front with the four that did fit, the sheet metal gradually lined itself up with all the other holes for a perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald L. from Cedaredge, CO
- Parts Used:
- WB17X210
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
the wires were not long enough to use the original path.
the original path was from the right front control knob around the back of the range and left side of range,which i dismantaled to install the new wires to the right front burner. When I found them to be to short I had to also dismantal the right side so the wires could be routed there. The new wires worked fine but did take some extra time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Coal Creek, CO
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The range kept giving an F2 alarm
When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from Plainfield, IN
- Parts Used:
- WB15K5068
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven handle broke
Removed the door and four screws to get to handle. Removed the two screws holding the handle and replaced with new handle. Replaced the four screws on the door and reconnected to oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cornelius from Hollister, CA
- Parts Used:
- WB7X7183
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
plastic sockets in end caps for connection screws broke off
Very detailed repair instructions on internet made installation of new end caps a job not needing a professioal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- don from Dallas, TX
- Parts Used:
- WB48T10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing racks
took the old ones out and put the new ones in their slots. No issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Georgianna from Austin, TX
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
End Cap broke on oven door.
It was easy as pie. Just followed the instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GAIL from STREAMWOOD, IL
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new drip pans
Not really a repair. But would like to say, I like the price and shipping was super fast. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Montgomery,, AL
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
welded supports for the surface elements were broken
unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from The Hills, TX
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Plastic end caps for oven door handle brokr off
When the replacement parts came (only took 2 days). I lifted the door off. Removed the screws that held the tempered glass front on the rest of the door. Removed the screws holding the broken end caps Replaced one end cap, inserted the handle, and fitted the 2nd end cap to the handle and screwed it in place. Screwed the front of the door to the back and replaced the door on its hinges. Easy as pie, ....Easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Los Altos, CA
- Parts Used:
- WB44K5009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Oven broiler stopped working. Had to replace the broiler element.
Just like the other responses described with two additional steps: 1) with a convection oven you have to remove the fan cover. It has four screws, the same size as the broiler element screws....but, get a piece of stiff cardboard the same width as the oven; put it all the way back, under the fan cover. There are holes in the oven bottom and your screws really want to roll into those holes and disappear; the cardboard will cover the holes. 2) as soon as you disconnect the element from the electrical wires....put a twist tie or other clamp on each wire as they want to fall back in behind the oven and you'll end up having to remove the build oven to get at the wires. The twist tie should keep them from falling out of reach.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from South Bend, WA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The door handle end caps did not fit on to the handle far enough. this caused the screw hole spread to be too wide, Also the new end caps had two nipples outside the bolt holes that the original brackets did not have.
The reason the brackets didn't go on to the handle far enough was there was a molding defect inside one of the brackets. After alot of scraping at the inside of the bracket and lightly tapping with a soft hammer I was able to get the defective bracket on so that the holes lined up to the mounting plate. As for the extra nipples I had two options. Either cut the nipples off or drill some holes in the metal plate that the brackets attach to. I chose the latter. I had to attach the brackets to the plate with extra long screws, reach in under the bracket with a scribe and mark the nipple location on the plate. Then I removed the handle and drilled two holes for each bracket. After some minor adjustments to the holes I was able to attach both brackets and reassemble the oven door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Cogan Station, PA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Broken oven door handle. Needed the brackets and screws to repair it.
removed the broken parts and screwed on the new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Muskego, WI
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke end cap while moving range
unscrewed broken end cap, removed from handle and replaced the new end cap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudine from The Colony, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
surface element not working
I simply pulled the old surface burner out, and plugged the new one in. It took less than one minute! The amazing part of this repair, is actually that PartSelect sent the replacement surface element burner OVERNIGHT! I could not believe it, and was VERY impressed with their commitment to help their customers in time of crisis. It arrived just on time for my Thanksgiving not to become a nightmare. Thank you PartSeclect!
Was this instruction helpful to you?
Thank you for voting!