EGR3000EL2CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Chris from Inglewood, CA
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Over not heating
1. Removed oven door..
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.
2. Slide out floor plate of over.
3. Removed four screws securing the flame shield.
4. removed the two screws attaching the heating element to the burner.
5. Pulled heating element wires out of rear hole in oven and detached plug.
6. Attached new element and reassembled in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARY from BIG LAKE, MN
- Parts Used:
- WB13K21
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not heat to the degree you set it for
I first took out the screw which held the bottom plate for the oven. then took the screws off the igniter unhooked the wires , took the new igniter hooked up the wires then put the screws back in put the bottom plate back in and turned the oven on to test it and it worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Mt Solon, VA
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Part will wear out after a couple of years
In my case it was the lower burner so I unplugged oven and turned gas off.
Then I removed the bottom drawer, and the lower burner cover.
Next unplug Oven Igniter, found where drawer existed.
Removed 2 screws attaching Igniter using nutdriver
Placed new Igniter on
Plug Igniter in and tested oven
Replace burner cover and drawer
This was much easier then what I went through with a repair man the first time around. These Igniter are designed for certain model stoves and are not interchangable with other model stoves!!!
Then I removed the bottom drawer, and the lower burner cover.
Next unplug Oven Igniter, found where drawer existed.
Removed 2 screws attaching Igniter using nutdriver
Placed new Igniter on
Plug Igniter in and tested oven
Replace burner cover and drawer
This was much easier then what I went through with a repair man the first time around. These Igniter are designed for certain model stoves and are not interchangable with other model stoves!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from OSSINING, NY
- Parts Used:
- WB29X36765, WB29K10005
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The burner caps were chipped and discolored.
I merely replaced the old caps with the new ones. It couldn't have been easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENDA from HENDERSON, NV
- Parts Used:
- WB29X36765, WB29K10005, WB29K10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Missing Burner Caps.
Caps were shipping very quickly. Price was very reasonable. Very happy with parts-selects service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Akshay from Bridgeton, NJ
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner had uneven flames
Too easy a five year old could do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Teddy from Bel Air, MD
- Parts Used:
- WB29X36765, WB29K10005, WB29K10003
- Difficulty Level:
- Difficult
- Total Repair Time:
- Less than 15 mins
GOT 1-SMALL 2-MEDIUM 0-LARGE CAPS
PLEASE BE ADVISED WHEN THEY SHIPPED THE BACK ORDER 1 -(taupe) LARGE CAP - RECEIVED 4 BLACK CAPS - 1-SMALL
2-MEDIUM 1-LARGE (ALL BLACK) - STILL LOOKING FOR
A LARGE CAP IN taupe color!
Received refund for 1-large cap
PROBLEM IS ALL OTHER PARTS ON THE GAS STOVE
ARE taupe in color - do not want black!
your advice?
2-MEDIUM 1-LARGE (ALL BLACK) - STILL LOOKING FOR
A LARGE CAP IN taupe color!
Received refund for 1-large cap
PROBLEM IS ALL OTHER PARTS ON THE GAS STOVE
ARE taupe in color - do not want black!
your advice?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Enrico from DURHAM, NC
- Parts Used:
- WB20K10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
F 3 code came on my panel, the oven wasn’t getting to the right temperature
I remove the old thermostat and realized right away it was burned, the replacement was very easy to clip on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from WARROAD, MN
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner had hot spots where the matieral melted some cause a distorted flame that would spit sputter
Remove the top grate and remove the top burner plate and then pull the burner out and remove the torx screw and adapter install onto the new burner and place back on the stove , good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from SAN JOSE, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven racks very old and writing on knobs worn ff
Very was ti replace racks and knobs. Very fast mail service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karin from ARUNDEL, ME
- Parts Used:
- WB16K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gas burner wasn’t burning properly
I ordered the new burner head and replaced it and now it works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from ROCKY POINT, NC
- Parts Used:
- WB13K21
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Igniter was glowing but would not light the oven.
Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlotte from CHICAGO, IL
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Existing oven bottom was damaged.
Removed two screws to remove old bottom. Insert new oven bottom and re-attach screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SAINT LOUIS, MI
- Parts Used:
- WB20K10015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Oven not lighting
Secured the power, Opened the back of the range, and discovered a rodent chewed the wires in half so I striped the ends and wired them back together, the oven works great !!
Was this instruction helpful to you?
Thank you for voting!