JGB450DEK2WW General Electric Range - Instructions

Took bottom cover in oven off with screwdriver . Then remove two small bolts with socket to igniter , unplug from under stove and pull out from inside oven. Reverse to install. Wala done and working great.

Removed oven door and warming tray. Then removed two screws holding the igniter in place. Disconnect the plug visible below the oven after warming tray removal. Installed new igniter in reverse order.

Had to use the wire nuts because the plug did not fit.
I used the old plug and spliced the wires.Thanks for the ceramic wire nuts.

Replaced the ignitor in the broiler. Two screws holding the ignitor in place and two to the cover holding the quick connect plug.

I was sure happy that they thought to add in the ceramic wire nuts. This Hotpoint stove had a direct wire, no wire clips like the new part had. I cut the wires and used the enclosed ceramic wire nuts. The stove works great. Parts Select helped in locating the model number which made this transaction a smooth one. Thanks. Always remember to turn off gas line and unplug any item you work on.

removed oven door racks and pan from bottom of oven. removed warming drawer unplugged oven igniter removed 2 hex screws from bracket on igniter. replaced with new one fiched wire down to warming drawer area plugged in. replaced door and warming drawer. works fine now. very ez to do!

I got my part in a couple of days during christmas and still got at pretty quick it was 5 screws unpluged the old one pluged in the new one put screws back and we were ready to cook, did all from inside the oven did not even move the stove very simple!!

It was quite easy. Uplug the ingnitor and remove two screws from bracket holding it in place along side gas pipe. Plug in new ignitor and and reinstall two screws thru bracket to secure ignitor against gas pipe. Thats it!! Oh, you must remove floor of oven (two Screws,back wall)and remove broiler and door/tray by pulling all the way out to access the ignitor and gas pipe assembly.

the part fit perfect so 5 min, done, thanks for the right part the frist time, I will be back

Unhooked old one, installed new one. Piece of cake.

I unplugged the power then removed the shield from in front of the valve location. I removed the wire shield and pulled the wire connector into the burner area. I unplugged the wire then removed the burner frame pulling it out, I removed and re-installed the igniter kit. I also had to cut the connector from the from the old igniter (about 3" up)then remove the connector from the new (cutting flush to that connector) and switched out the connectors using the porcelane wire ties provided with the new unit. I then re-installed the burner frame making certain that the wires were in the proper location. I plugged the connectors together ensuring proper locking, pushed the wires back into the hole, replaced the wire shield and then the valve cover shield. Restored power the igniter lit brightly and approximately 4-5 seconds later the oven burner lit. I checked connector because another person on the site stated that it may be the wrong one and that the wire connectors would be sent in case that were so.

remove the door, removed about six screws and did a clean up on the glass. the replacement part was screwed back in place. so easy

First removed 3 screws at burner front and back then pulled out lower storage drawer to disconnect plastic connector, removed and had to cut plastic connectors to use ceramic wire nuts (supplied with parts box) I had to work from underneath stove as well as in the oven it self, if the main door is easily removable it would have helped a great deal but four hours later

I followed the directions that I read online and the job was a breeze. I started by disconnecting the electricity, and sliding the oven out from the wall, then taking the oven floor cover off, then ordered Chinese, received a phone call from my sister( blah,blah,blah), Disconnected the old piece, paid for Chinese Food, ate Chinese, installed new piece, reinstalled oven floor, reconnected the electricity, pushed oven back into place, lit oven, turned it off and then tested it again. All in less than an hour.

I went on youtube and found videos for similar problems. Then was shown how to test the part to confirm if it was good or bad. After testing with an amp meter I confirmed that the ignighter was bad. I ordered the part and got it in 3 days. I put in the new ignighter turned on the oven and placed inside the oven a temperature gage, when the timer rang on the stove confirming that the oven was up to temperature, I opened the oven door and the temperature gage read 350 deg. exactly the temperature I had set. So for under 50.00 I fixed the oven, a service call would of been 80.00 plus parts. Thanks for the help. Bob Murphy