JGB635DEK3BB General Electric Range - Instructions

Disconnect power. Remove oven door, oven racks, bottom pan, drawer below the oven. unsnap igniter wire connector. Remove two screws holding the igniter in place, remove igniter.

Install igniter (placing igniter wires away from any heat producing parts) and all parts in reverse order as they were removed.

Oven heats good now, makes great cornbread and biscuits, the wife helps the oven do this.

removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.

Put in a new foot / bumper. That's it.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

Pretty easy in all. The connector from the igniter to teh power sorce didn't quite fit. Ijust cut off the new one and spliced the old one back on. Probably could have made my life easier if I took off the oven door, but it just meant I had to reach more. Works great, and other the connector, which I didn't really think would fit a 15 year old oven,it was very easy/.

This would've been an easy repair, but I ran into some complications.

First I removed the thumb screws holding the bottom oven pan, took the pan out, and also took the bottom panel off the front of the oven.

This gives you access to the burner assembly. I disconnected the wire to the ignitor. I then removed one screw at the front, and two in the back of the burner assembly with a 1/4 socket wrench.

The burner assembly came out. I tested the ignitor for continutiy with a multimeter to ensure this was the faulty part. There was not continuity, so I knew the ignitor needed to be replaced.

This was when I tried to unscrew the ignitor, and both screws stripped their threads on the burner mounting plate. Complication #1. Seems with age, that mounting plate tightened up on the screws.

I cut the screw heads off with a dremel and cutting wheel to get them out. I'm glad I did this before ordering the new part because I needed to order the replacement screws too.

The burner mounting plate for the ignitor needed to be re-tapped to get the new screws in with a 10-32 tap and power drill.

Once the mounting plate was properly rethreaded, I attached the new ignitor, and reattached the burner assembly to the oven.

When trying to connect the wires, the plastic connectors wouldn't click together. They matched up fine, but wouldn't go all the way in. Complication #2. While the plastic connectors were properly mated, the inside pins were both female. The old ignitor had male pins on it, the new one had female pins. So I removed the burner assembly again, cut off the new ignitor connector and spliced in the old ignitor connector with the included porcelain wire nuts.

I put the oven back together again, fired it up, and it worked great.

1. Unplug from electrical outlet. 2. Turn off gas valve. 3. Remove oven door. 4. Remove bottom drawer. 5. Remove oven shelves. 6. Remove oven floor, take out the two screws at the rear. 7. Unplug the igniter from the wire harness, you can reach it from where you removed the drawer. 8. Remove the igniter, by unscrewing the two bolts using your nut driver. 9. Replace with new igniter. 10. Put everything back together, starting with # 9 and work your way to #1.

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A screwdriver is the only tool required.

I cut the box open with a utility knife and removed the grill. I then opened the oven door and rearranged the two existing racks so that the third one would go in so they all have the same distance between each of them. I slid the new rack into position. It didn't go in smoothly though as I had to push it in and out several times so that it would line up perfectly. Finally in went in all the way. Then I closed the oven door and went and sat down to think about the wonderful job I just did.

replace sensor

I removed the door and the racks, and the flame spreader. I removed the 4"X6" shield loosen the circular flap to plug the new igniter to the recepticle. Turn the oven on to check the operation and if it comes on, button it back up. remember open the oven door approx 3" and pull upwords to remove the door. I would say 90% of the time the igniter is the problem.

I followed the video instructions on the site. I unplugged the power supply and turned off the gas supply. I then removed the plate out of the bottom of the oven to get to the igniter. Then I removed the screws and unplugged the igniter to remove the old part. I had to purchase two porcelain wire nuts because the new part connection did not match up with the old connection. The repairs were quite simple and I had my oven back and working in no time. I am glad I read the comments from others because I thought it was my gas control valve, but they were right it was my igniter. This saved me time and money.

I pulled the oven door off the hinges and took the bolts out of the bottom of the over that were holding the strip on. I then pulled the strip off and replaced it with the new on. I replaced the bolts and then replaced the door on the hinges.