JBS360DM1WW General Electric Range - Instructions

took the old one out and dropped the new one in, replaced the electric burner and done

thw worse part was paying as much for s&h as i did for the part itself

The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back panel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.

I removed the new control panel from its packaging and noticed that the button overlay was not included. I grabbed a putty knife and carefully loosened the adhesive on the old panel and was able to apply it to the new control panel. After installing it I looked up the number of my old panel on the included paperwork and simply entered the “profile” number after powering up the new one and It worked perfectly. I was very relieved to not have to buy a new range!

I picked the least expensive and most likely issue with our oven that was not indicating a correct oven temperature. I am sure with a 15+ year appliance that the circuitry is on its way out but wanted to give this a try to avoid a new appliance purchase. Oven pre-heat setting takes much longer to finish with the age of the oven. However, after the new sensor the oven will maintain a more even temperature for the cycle.

Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.

At best a temporary fix for a an appliance this old.

I removed the 4 hex head screws holding the control panel , then the other 4 slotted screws. Disconnected all wires being careful to keep track of the color coding. Had a little trouble with the adhesive holding the face plate( I don't know why they even used it). Put the new panel in and reconnected it. Re set circuit breaker and tried the oven. It still wouldn't heat. it wasn't the control panel, but a burned out wire connecting the element in the back of the oven. Well, anyway I learned how to do the job and the the new panel activates better, so all was not lost.

I unscrewed two screws inside the over over the element. Then I slowly pulled the element out and unplugged the two wires attached. Afterward I pushed the element back in place and screwed it back in and was done. Sure saved $550 I thought I might have to spend on a new oven,

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the wires to the new element and reinstalled the two screws. A brief test showed the element worked and that was it.

every thing went great

I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!

Removed the hexagon screws. pulled the unit out and wiggled the tabs loose disconnecting them. Installed the new unit-attaching the tabs making sure they were tight. Put the new unit through the opening in the back of the oven and reattached the hexagon screws. Back in business in about 10 minutes.

Removed two screws, and replaced element with a new one. Easy, works great.

Remove door and disassemble door to gain access to inner glass by removing 8-10 screws and nut driver screws remove and clean outer doors remove heat shield and heat Insulation. Reinstall careful to not get fingerprints on inside of glass and replace quick release hinges and door. Careful of hinges as they are spring loaded

First my son removed the two screws that held th element in place but first please tell everyone to turn off the breaker first. My son did not and he had gotten a shock from this and burned his hand. I think this is very important first. After cleaning up his hand he then replaced the element and tested it and it worked nicely.

Thank you for your prompt delivery and the correct part.

Sincerely
Kelly Didsbury

took nut driver to remove the old and replaced with new. simple.

Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..