JSP26BD2WH General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- TESS from BOSWELL, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
element broke, oven wouldn't heat - still doesn't
first husband removed the bolts unplugged old element wires -plugged in new element wires and but in bolts - unfortunately the oven still doesn't work not sure if element is bad or wiring, need professional help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Dayton, NJ
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element was not working in an old (50+ years old)GE electric oven
Replacement of the heating element only takes a few minutes...First, turn off the breaker/fuse to the stove, then just remove two screws , pull out the two connected wires to expose the connections, hook them up, and replace the screws to the cover plate. The connection/cover plate can be hinged or not hinged. Make sure you order the correct one. We ordered the wrong one at first, but were assisted by the returns dept. and received the correct one in 2 days. Great customer service, thanks partsselect.com!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Muncie, IN
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Tenant broke bake element
Removed the two screws, pulled out old element, installed new element, and reinstalled screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Garden City, ID
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed New Burner Bowls
Removed the old burner bowls, replacing them with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shawn from port richey, FL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The element on our three year old stove stopped working...this was the bottom bake element.
It was surprisingly simple. All I had to do was shut the breaker off to the stove(safety first). Next open the oven door and use a flashlight just to help you see,and unscrew the two screws holding the element in place on the back stove wall. Next slide the stove away from the was to give yourself enough room to access the back of it(you may need to unplug it to get it out far enough. My model had a cover over the back that took six easy to remove screws. Once the back cover was off I could easily see where the element was plugged into, so i removed the wires from the end of the element(just female terminals slipped over the end) i then went back to the front of the stove and pulled to element out.
To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple
To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Charlotte, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
My heatng element blew up
I followed the way all the others on this website did the repair. It was so easy. I turned the power off to the oven, then disconnected it from the back oven wall, pulled it out a bit, disconnected the wires, and put it back in.
Then we put the power back on and stood back and turned on the stove and IT WORKED!!! Yeah, and for so little money... I tell you I shopped other websites and this one was priced GREAT, and just reading the stories how others had done this repair gave me the confidence to do it too. Now, I think I have a burner that I will replace and who knows what else I can find to do.
THANKS SO MUCH!!!
Then we put the power back on and stood back and turned on the stove and IT WORKED!!! Yeah, and for so little money... I tell you I shopped other websites and this one was priced GREAT, and just reading the stories how others had done this repair gave me the confidence to do it too. Now, I think I have a burner that I will replace and who knows what else I can find to do.
THANKS SO MUCH!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from State College, PA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The bottom bake element was burned out.
1. Turned off electrical breaker for range.
2. Removed the two hex head screws that hold element in place.
3. Pulled element out and unplugged the two electrical connectors.
4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way.
5. Apparently some of the insulation had fallen down and was blocking the area where the element slides in.
6. I used a long thin screwdriver inserted into the two holes to push the insulation aside.
7. The element was then able to go in all the way.
8. Replaced two hex head screws.
9. Turned on range breaker.
10. Turned on oven. Works fine.
2. Removed the two hex head screws that hold element in place.
3. Pulled element out and unplugged the two electrical connectors.
4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way.
5. Apparently some of the insulation had fallen down and was blocking the area where the element slides in.
6. I used a long thin screwdriver inserted into the two holes to push the insulation aside.
7. The element was then able to go in all the way.
8. Replaced two hex head screws.
9. Turned on range breaker.
10. Turned on oven. Works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from west sayville, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
bake element broke
first i removed the two screws that hold the element in place. then pulled the element out about 3 inches and disconnected the two wires .then i connected the two wires and pushed thebake element back and replaced the two screws.then i put the circuit braker back on and tested the stove and it worked great. very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- fred from PALM COAST, FL
- Parts Used:
- WB08T10002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
shortage in wiring cause the housing to burn out
Replaced new light housing.
Thanks to you guys for the prompt response
Thanks to you guys for the prompt response
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MARTIN, GA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
bake element was fried
I went by the video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from BLUFFTON, SC
- Parts Used:
- WB30M1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken heating element
remove broken heating element and install the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PROVO, UT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls were badly tarnished . . . shine could not be restored.
1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Franz from CRESTVIEW, FL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not heat
Removed old broken element and installed new one. Took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from WEST WARWICK, RI
- Parts Used:
- WB30M1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
a plug on the element broke off while cleaning and replacing
Absolutely no tools required for this task. Simply align the prongs to the female portion on the stove top. Carefully push in until the element is in place then line up with the drip pan slot. No instructions are necessary!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!