C2S900P2M1S1 General Electric Range - Instructions

Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time.
Otherwise everything was great!

Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.

Replaced new light housing.
Thanks to you guys for the prompt response

It only required placing the new burner in the proper location.

took burner off installed new one thank you for fast shipping

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

I order this parts only take me 5 second to install i realy love love this parts i recommen to people to order you are the best

Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .