JBP21BY2 General Electric Range - Instructions

I unpluged stove then opened slightly oven door and lifted it off to get closer. Then with a light to help I took out two screws and pulled the element out. I didn't need pliers to get the wires that are put on with slide on clips. you may need a pair. put wires on slide in place put screws back ,replace door, plug it in and test. Very easy.

No brainer. No tools. Remove burner, lift out old drip bowl, drop in new one, plug in burner, voila! Done. 10 seconds.

Absolutely no tools required for this task. Simply align the prongs to the female portion on the stove top. Carefully push in until the element is in place then line up with the drip pan slot. No instructions are necessary!!

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Unplugged oven. Pulled out from wall and removed backside access panel. Unplugged 2 stake-on connectors connected to element. From front side of oven, removed fan guard using 1/4 inch nutdriver. Gained access to and removed two screws holding in element. Pulled element out. For installation, reverse process.

Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!

I removed the two screws that hold the element in place. I pulled the element out about three inches and
disconnected the two wires. The screw holes in the new element would not accommodate the old screw size so I enlarged the holes to fit. Connected two wires and replaced two screws that hold element in place. End of story.

First I unpluged the appliance. Then I removed the cover from the back of the range. I then disconnected the two wires from the element. I then removed the two screws that hold the element in place. I then removed the old element and reversed the process to install the new one.

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 220 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

It didn't get repaired. Put the existing screws into the cap and the screws chewed up the slot it was to go into. Destroyed the end caps L and R. Only fix appears to be an new stove.

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

Flipped off the breaker for the stove. There were two screws holding the old element in place. Removed those, pulled the element out a little to expose two wires, disconnected those, swapped in the new element, reconnected the wires, and screwed it back into place. Flipped the breaker back on and voila! Barely more difficult than changing a lightbulb.

removed heating element,removed old drip pan.added new drip pan,replaced heating element.Took less that 3 min.

Everything was very easy: identifying the right part was very easy on the website, the part came quicker than I expected, and my wife replaced the stove element before I even got home from work. She just pulled the old one out like she would to clean the top of the stove, and put the new one back in. Have had several awesome cups of coffee since the replacement.