JB655DK4CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pam from Daphne, AL
- Parts Used:
- WB27X45466
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven control panel was blacked out..no clock no start.
Took out the old control module and removed the sticker and reattached sticker to new part and installed the plugs, put the screws back in and it started working, thankyou so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Bradenton, FL
- Parts Used:
- WB27X45466
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Mother board was blown
Purchased the board installed it and saved about 130 dollars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roman from West Chester, PA
- Parts Used:
- WB04T10086
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Spilled 1/2 gallon Hot wax on stove
Took door apart to clean inside of glass door. scraped most of the wax from the stove 99%. Could not get the last 1%. Cleaned all parts. Put door back together again, put the door seal on after I got the right one. Had to reorder a new seal(one that was actually made for that model) messed up the first one and whalla! Took about 3 weeks to clean off the wax from stove and the surrounding area. Stove is good as new. Thanks for the quick service. Would definitely recommend and use you guys again. Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Lansdale, PA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hard to move drawer in and out because the rear drawer supports broke off.
Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Stuart, VA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic slide for storage drawer broken.
Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Salem, OR
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Flashing F2 and erratic temperature readings.
Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Woodinville, WA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our bottom drawer support broke and the bottom drawer was canted
Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daryl from Savannah, TN
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bad control board
Removed top back plate of oven. unpluged all of the wiring plugs on the control board. Removed two screws on the control board. Removed face plate from old control board and put it on the new control board. Atteched new board with the two screws. Connected all of the plugs to new board ( all plugs are color coded to board). Re-installed oven back plate. Pluged oven in. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lisle, IL
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven not warming, f2 indicating overheat
Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Shakopee, MN
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Stove drawer rear guides broken
Installed new guides with a nut driver without any problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Austin, AR
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
clock, over control, oven light , timer did not work
remove rear panel cover, removered four screws that held control panel, disconnected colored wires, removed circuit control board, reinstall new board and connected color coded wire to the correct spot on the board, plugged in 220 volt cord, switch on circuit breaker, everything worked normal again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Newark, DE
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Range lower drawer would not stay on track.
Easy to install replacement parts using the screws provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from Deer Park, WA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken drawer support
Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from RICHMOND, VA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
rear drawer supports broke
Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wallace from Demorest,, GA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bottom Heating Element not heating up.
I miss diagnosed the situation at first. When the top element only heated up I thought the control was the problem. Wrong. Apparently both elements heat up during initial start up. It turned out that the bottom element was not working so it needed to be replaced rather then the control. Now both are replaced and the oven is now back to original status. Entire repair cost about $80. I saved over $100 by attempting this myself. Easy fix. Obviously I am not a pro. My local hardware store had a generic heating element that worked just fine and only cost $22. Two screws to repair after removing the back panel. Remember to pull the plug before you begin and after the repair put all panels back on before plugging back in. Pizza anyone?
Was this instruction helpful to you?
Thank you for voting!