JB625GK4SA General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dock from Aurora, CO
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The storage drawer came without supports.
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from N CHESTERFLD, VA
- Parts Used:
- WB14X41386
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Oven door wouldn't close properly
Watched video on you tube. Removing/reinstalling all of the screws/bolts took longer than the actual repair.. Took 23 minutes total from turning power off, repairing and turning back on. Super easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from CLAWSON, MI
- Parts Used:
- WB44X45494
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
baking element was burned out.
unscrewed element from back of oven disconnected power source. Replaced new element & screwed new wires onto back of oven. Took 5 mins. Works like new. I am 73 yr old female so anyone can do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from LONGS, SC
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
oven door gasket needed replaced
Ordered the part, it arrived and 5 minutes later it a complete installation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent J Paola, from GREENWEL SPGS, LA
- Parts Used:
- WB27X45466
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bad Line fault displayed on range clock
1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Using a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SAN TAN VLY, AZ
- Parts Used:
- WB21X22134
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not Reaching Temperature above 300 Degrees
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from SAINT PAUL, MN
- Parts Used:
- WB02X38986
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacing handle spacer
This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from JACKSONVILLE, FL
- Parts Used:
- WB04T10086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced oven door gasket
Remove old stained gasket and replaced with new. Only $57.00!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from WEBSTER, TX
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Caitlin from MOUNT SHASTA, CA
- Parts Used:
- WB14X41386
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Handle would not pull the latch back any longer
Super easy repair! There are videos online if you have one type of oven, I had the other type (with the little silver plate right above the latch part). The trick is to remove the handle from the assembly itself before removing or placing it in the oven. 4 screws total and I recommend needle nose pliers to help remove the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominick from THORNWOOD, NY
- Parts Used:
- WB27X45466
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven no longer working after running the self clean option. Only Stove top burners worked
I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.
To Install.
Reverse steps above
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.
To Install.
Reverse steps above
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Kidder, MO
- Parts Used:
- WB04T10086
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Hole in gasket
I took the oven door off. Laid it down on a blanket on the floor. I pulled up on end going into the door, then went around with fingers to feel where the clip were and grab the clip with my fingers and gently pulled up. Then grabbed the new gasket, found the center clip that goes at top of door and started pushing the clips in. The last was feeding the ends back into the slot in the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Calumet City, IL
- Parts Used:
- WB44X45494
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
8' ELECTRIC ROUND HEATING ELEMENT
THE TWO 8' ROUND HEATING ELEMENT
1. LIFT THE LID OF THE STOVE FROM THE SIDE. SOMETIMES YOU MIGHT HAVE TO PRY IT A LOOSE. BE CAREFUL HOW YOU LIFT IT FROM THE BOTH SIDES WITH A FLAT SCREWDRIVER.
2. BECAREFUL HOW YOU PRY THE WIRING FROM THE OLD HEATING ELEMENT. THE WIRING IS FRAGILE. REMEMBER THE STEPS YOU TOOK TO TAKE A LOOSE THE OLD ONE. I HAD MY SON TO HELP ME BECAUSE I FIRST PULL THE CLAMP BACK WITH THE SCREWDRIVER AND HAD HIM TO HOLD IT TO OLD ONE STILL HOOK UP TO THE WIRING. I PLACE THE NEW ONE IN THE CLIP. THEN I TOOK ONE WIRING AT A TIME TO THE NEW ONE.
1. LIFT THE LID OF THE STOVE FROM THE SIDE. SOMETIMES YOU MIGHT HAVE TO PRY IT A LOOSE. BE CAREFUL HOW YOU LIFT IT FROM THE BOTH SIDES WITH A FLAT SCREWDRIVER.
2. BECAREFUL HOW YOU PRY THE WIRING FROM THE OLD HEATING ELEMENT. THE WIRING IS FRAGILE. REMEMBER THE STEPS YOU TOOK TO TAKE A LOOSE THE OLD ONE. I HAD MY SON TO HELP ME BECAUSE I FIRST PULL THE CLAMP BACK WITH THE SCREWDRIVER AND HAD HIM TO HOLD IT TO OLD ONE STILL HOOK UP TO THE WIRING. I PLACE THE NEW ONE IN THE CLIP. THEN I TOOK ONE WIRING AT A TIME TO THE NEW ONE.
Was this instruction helpful to you?
Thank you for voting!