JBP24BY2 General Electric Range - Instructions

I followed the instructions given to me in the package and all went well. I cut the old wires off the burnt terminal block, stripped the wires, installed the wire nuts with the shrink rap, installed the new terminal block and burner. The new burner is working great! Thanks

I removed the old drip pans, cleaned the range top, washed and installed the new drip pans and put the old pans, box and packing materials in the trash. In only 12 minutes my range top looked like new and the mess was picked up. Now, if I could just get the rest of the kitchen looking that good that fast!

I simply replaced the element. HOWEVER, the most wonderful parts of this repair...Because of the pictures and closeups and descriptions I knew exactly 'what' to order! And I had the replacement in less than 24 hours. I can do some home repairs but this company provided such detailed information AND speed of delivery...that this was a no-fuss fix. I'll definitely stop by to buy, again. Thanks!

We tried to find the replacement pans at the local hardware store and were disappointed in that although they were cheaper, they were not deep enough to handle the heating elements. We were delighted to find that the parts from PartSelect.Com were genuine GE parts... installed in minutes and were delivered VERY quickly!

No repairs, really-just replacement, but I have been looking for the burners for three and one half years, and PartSelect had exactly what I needed for this old stove!
Theyalso had the electric element that I bought in the next order.

After staring at the online pictures of possible replacement bake elements, trying to count the number of squares to figure the length and width of available oven bake elements (some of the pics had listed measurement some did not), I settled on a push on element, since there were no matching screw in elements that appeared to come close to the measurements needed. Since it was a push on, I had to drill out the holes a bit more to fit the screws which took some time and finesse. It appears to works and it at least has enabled me to put off my bigger decision of buying a newer oven for a bit.

unpluged unit then removed back panel unpluged element then took the two screws out took old element out replaced with new one put screws back plug element back in put back panel on pluged it in and started baking home made chocolate chip cookies

First, we ordered the part on Sunday afternoon online. It was here by Tuesday morning. We unplugged the oven and removed the screws holding the element in place and the electrical contacts. That was the toughest part because it's hard to get in the oven and they were baked on pretty well. We had to drill holes in the bake element. Be careful not to drill them too big, so the screw will fit snug and make contact. We screwed the bake element to the contacts, then back to the over, plugged it in and turned it on. The temperature is more constant and steady than ever, and the oven heats much faster. We were impressed and happy to avoid replacing the whole stove.

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

The only hard part about putting in a new terminal block (and this time I had to replace the burner too, because that fried too) is stripping the stove wires, because that thermal insulation is very hard to get off. Otherwise, it's simple. In this case, I had already replaced this one (sigh), so had already cut & stripped the wires, so it was all easy. Frankly, the sane thing to do is buy a new stove, but wife is too cheap.

Removed burner trays, pulled out heater unit, cleaned up inside of area around all four burners, slipped the burner trays back in and pushed the heater unit back into place.

Lined up the prongs and slid it right in, took 30 seconds.

This was extremely easy! I unscrewed two screws, pulled out the old element, inserted the new element and screwed the screws back in. Also, this part came very quickly through the mail. If needed, I will definitely use this site for repairs again.

just put in the new part

unplugged the element took the old pan out and put the new one in, plugged the element back in.