JB576GR6WH General Electric Range - Instructions

raised hood, removed four screws that hold the top plate.
placed in new insulation and replace top plate.
ran oven at 500 degrees for 20 minutes. all OK.

First turned off the power to the stove at the breaker panel, thenI removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Disconnecting/reconnecting the "clips" was the only difficult part because they did not slip off/on easily. Replaced the element in the oven, replaced the screws...good to go!

Best part of buying from Parts Select was that they shipped the part the same day I ordered it, which was the Friday after Christmas. Competitor would not have shipped till the following Monday and we needed the oven ASAP!

Instead of flipping circuit breaker, we pulled the oven away from the wall and unplugged it. Used socket wrench to loosen screws of bracket holding old element onto the back oven wall, then gently pulled element until connecting wires appeared. Removed the 'clips' attached to the old element prongs and discarded old element. Reattached the 'clips' to new element prongs, then gently pushed prongs into back into oven wall until the bracket was flush with the wall. Used socket wrench to screw and tighten the bracket into place. Plugged in the oven and tested the new element to make sure it worked. The whole process took only a few minutes.....it took longer to clean the oven before installing the new element.

The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!

first husband removed the bolts unplugged old element wires -plugged in new element wires and but in bolts - unfortunately the oven still doesn't work not sure if element is bad or wiring, need professional help

1. Turned off electrical breaker for range.
2. Removed the two hex head screws that hold element in place.
3. Pulled element out and unplugged the two electrical connectors.
4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way.
5. Apparently some of the insulation had fallen down and was blocking the area where the element slides in.
6. I used a long thin screwdriver inserted into the two holes to push the insulation aside.
7. The element was then able to go in all the way.
8. Replaced two hex head screws.
9. Turned on range breaker.
10. Turned on oven. Works fine.

Pulled out bottom drawer and showed my 13 yr
old boy that the spring needed to go back in same hole, then he did the rest. It was so easy, even a 13 yr old can do it.

Removed oven racks and took the opportunity to clean my oven. Then removed the two hex head nuts holding the burner assembly in place. I slid out the burner (very slowly) hoping the connectors were intact and that there was enough lead wire to make for an easy repair. Yes... there were 2 inches of lead wire. It took a couple of minutes to swap out the parts and... success!
Don't forget to turn off the circuit breaker before starting repairs.

Followed the instructions from the video. The repair was really easy and quick.

All I had to do was just unscrew the bolts,pull out the old one, and put the new one on its metal clips and then rebolt.So easy and I know I would have had to pay much more then what I did for the part..This place is super.I ordered my part one day, and it was there the next...Sandy

.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

I turned off the power going to the stove, unscrewed the 2 screws, plugged in the 2 inserts, put the 2 screws back and PRESTO!!!!

Removed the two screws, pulled out old element, installed new element, and reinstalled screws.

It was surprisingly simple. All I had to do was shut the breaker off to the stove(safety first). Next open the oven door and use a flashlight just to help you see,and unscrew the two screws holding the element in place on the back stove wall. Next slide the stove away from the was to give yourself enough room to access the back of it(you may need to unplug it to get it out far enough. My model had a cover over the back that took six easy to remove screws. Once the back cover was off I could easily see where the element was plugged into, so i removed the wires from the end of the element(just female terminals slipped over the end) i then went back to the front of the stove and pulled to element out.

To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple

Parts Select is the only parts place I found on the internet that had what I needed on my first purchase, so when I needed these clips I naturally went back to them. Product was easy to find, price was fine, receipt for payment quick and more importantly receipt of item was super quick. Thanks to the efficiency of this place and my old appliances, I will continue to go to them as needed.