JP385 9R1BL General Electric Range - Instructions

I turned the power off to the stove (very important). then I unplugged the heating element from the terminal. I then unscrewed the terminal from the range top and pulled the terminal through to expose enough wire to do the job. I then proceeded to cut one wire from the old terminal and twist the new wire onto the wire that goes to the switch. Then I capped it off with the electric cap that came with the new terminal. then I covered the exposed wires with the sleeve that came with new terminal. Then I did the same exact thing for the second wire. After that was all done I put everything back together and turned the power back on.

I simply pushed the new burner into hardware. I then tested it to see if it works. . .

I simply pulled out the old element. Plugged in
the replacement, which arrived very quickly, and
that was it. I couldn't believe that was all there
was to it. I really loved being able to order the
replacement part online. Intend to order more
replacement parts just to have my stovetop
looking like new again.

After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.

I took off the old parts then I simply changed the drip bowls and plugged in the new elements!

Thanks to your excellent illustrations, I was able to find the pieces very quickly.
Outstanding service, speedy delivery.

Removed old burner, plugged in new burner. Turned on electric and everything worked fine. I was concerned that I would not be able to get the correct burner since my stove is approximately 30 years old and General Electric no longer stocks replacement parts. The new surface element was manufactured by General Electric and had the correct replacement number on the package. Thanks Part Select.

Turned off the power to the stove top and remove the blower capacitor installed the new capacitor. Turned the power back on and it worked.

Hi, Very simple fix.Take out 1 screw & clip wire with snips. Put wires from new unit together & screw on wire nuts. Put shrink tubes on & heat with liter till it shrinks to what you want. A $15.00 fix is better than a $500.00 stove. FIRST STEP TURN OFF THE BREAKER & YOU ARE GOOD TO GO!!!!! Ron

In a little over 15 minutes, I was able to pull the element and pan, snip the wires on the terminal block and use the wire nuts to fasten the new terminal block. The shrink wrap tubing went into place easily and all went back together easily. Best of all, the two year problem of a poor element connection was solved in a matter of minutes for a few dollars.

unplugged the burners, took out the old drip pans, put in new drip pans then plugged in new burners into the burner outlets, very easy and looks like new!

Pull out oven/range unit. Lift range top all the way up. Remove old terminal block. Make electrical connections using supplied wire nuts & heat shrink tubing. Heat shrink. Replace range top. Install coil burner & burner pan as unit. Done.

Had one burner that was completely out as the old terminal block had a broken contact. The other burner was intermittent and would arc when heating up. There are several slightly different size terminal blocks. I had a hard time re-inserting one of the old burners into the new terminal block but got it to seat. I put a new burner with the new block on the other one and it fit much better. Additional tools used were a wire stripper and a heat gun for the heat shrink. The stove works great now.

Pulled out the 8 inch surface element and then used a 1/4 inch socket to remove mounting screw for terminal block and pulled out block with attached wires as far as wires would permit. My range top does not lift up so I had to work thru surface opening but there was at least 10 inches of wire to pull out so it was not a problem. Cut existing wires at block, stripped 1/2 inch of insulation using my wire stripper pliers and wrapped wire ends of new terminal block and secured with wire nuts provided. Slipped on shrink insulation provided and applied flame from a hand held butane lighter. The instructional video on the web site was a great help. I may not have done repair without first watchng how easy it is. A cheap wire stripper is a great help. This supplier made it easy to select parts with fast delivery and complete the repair. Great source of appliance parts.

unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.

I took the old ones out and put the new ones in. No problems. Good fit. Looking back I should have ordered new elements as well but could not afford them now. I appreciate the ease of ordering and the speedy delivery of these items and will definitely use Part Select again when needed. Thank you for your assistance.