JM93R4 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from JONESBORO, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Burnt into
Two 1/4 inch screws and then two Phillips head screws that was it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from Fresno, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
baking element burned out
Removed the nuts securing the element to the back of the oven, pulled out the wiring and unscrewed the wires. Went on line and found the part, ordered it, received really quickly and put the part back in the oven. Works great. Oh, I also turned off the power.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Lima, OH
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The Bake Element in the oven had "blown out" on the right side, and wouldn't heat.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I connected the two wires to the new element with the screws provided and simply replaced the screws that hold the element in place.
In 20 minutes the job was done. It was a snap to make the repair!
Then I connected the two wires to the new element with the screws provided and simply replaced the screws that hold the element in place.
In 20 minutes the job was done. It was a snap to make the repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from DANVILLE, KY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Heating element severed
Removed old new one fit perfectly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from TABERNACLE, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Burnt out element
As instructed in your directions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary C from KISSIMMEE, FL
- Parts Used:
- WB44X200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Baking element broken
Turned off the power to the stove, pulled out the racks, unscrewed the old element and pulled off the electric connectors...easy so far...installed the new element to the electric connection, pushed back into the back of the stove and reinstalled the screws. Turned on the power and then the stove...now I can bake an apple pie!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from CLAYMONT, DE
- Parts Used:
- WB44X200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
second time repaired in about ten years
removed parts from carton,,shut off breaker to over,,cradled the flash light,removed cover plate,,removed element,,removed screws from wires,,reversed to install,,screwed wires to element,,placed element in place and installed plate nuts,,,turned breaker back on...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from SPARTANBURG, SC
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burnt bake element
Removed door. Take out two hold down screws for element. Hold electrical tab with pliers and remove screw on each tab. Reverse directions to reinstall. Door may have screws to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from RICHARDSON, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
Bake element burned out
Turned off power. Then loosened two nuts at back of oven. Pulled out old element and inserted new element. Tightened two nuts and turned power back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Evergreen Park, IL
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Simple, unscrew and then re-screw
Simple, unscrew and then re-screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Northborough, MA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven heat was very uneven.
I removed the screws that held the element in place. This was the most difficult part because clearance was tight between the screws and the element. I gently pulled the element out enough to expose the wire connections. I disconnected the wires and removed the element. Installation was the reverse - connect the wires, re-position the element, re-install the final screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Grand Blanc, MI
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bad Bake unit
Had my youngest son removed the two nut screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Removed element and installed new element in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Steubenville, OH
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't heat
First I removed the two srews that hold the element in place. I then pulled the element out about three inches and disconnected the two wires. I attached the wires to the new element and we had our oven working again. I really am happy with the timely service I received from PartSelect and would recommend them to anyone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Alameda, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Lower bake element was cracked
First, I shut off the power to the oven... no point in risking a nice electric shock. The next thing I realized was I could not see anything... enter the flashlight. Then, well then it was really easy. I removed the two screws that held the element to the back wall of the oven, pulled the element (and some of the insulation stuffing) out about 2 inches to reveal the two wires and their connecting screws. Unscrewed them, put the new element in, reconnected the wiring, restuffed the stuffing and reattached it to the oven wall. Turned on the power and she heated up faster than ever. Speaking of fast, my part arrived the day after I ordered it and that was with regular shipping. Thanks fellas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Mount Laurel, NJ
- Parts Used:
- WB44X200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake Element didn't heat sufficiently
Turned off circuit breaker, took two screws out to be able to pull element out from back. Took two more screws out to remove old element from oven. Did the opposite to install the new bake element. Turned power back on, and it worked fine.
Was this instruction helpful to you?
Thank you for voting!