JKP18G1K2 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michelle from Pasadena, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element broke in several places
Turned off the power source to the oven. I then removed the two screws that hold the element in place, then pulled the element out about 3 inches and disconnected the two wires at the back. The hardest part was getting the screws turned to connect the new wires at the back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Highland Village, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken Element
The repair was very, very easy. The hard part was locating the part. I could not find it at any local hardware store. Went on-line and ordered part with PartSelect.com and it was at my front door the next day. The job was done in less than 15 minutes later. Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Wauwatosa, AL
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Old element burned out
Turn off power to oven. Make sure with tester that the power is indeed off. Disconnected the two fasteners holding the old unit face plate to rear of oven. Pull the unit outward to expose the leads. Disconnected the leads. Reform new element to remove minor bends so it will sit flat on the floor of the oven. With plies holding the leads straight connect new unit to oven leads. Push new unit back into mounting hole. Reconnect new unit face plate to back of oven. Check that unit is level. Turn the power back on. Test the unit. All works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman from Houston, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven bake element broken
Took out the old (removed 2 screws holding the element to the back of the oven, disconnected the 2 screws attaching the electrical wires to the element). Decided to clean the oven with EasyOff. It took longer to spray this on, and then later wipe it up, than the repair itself. Reversed the procedure for the new element. A very simple repair - my wife is amazed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Saint Louis, MO
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Old element burnt out.
No instructions provided, but not needed. Removed two screws holding element in place. Removed two screws connecting element to power wires. Installed new element using reverse process.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Paducah, KY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bake element was burned out.
Safety first! Flipped breaker for oven in main breaker box.
Removed two screws that hold element in place.
Pulled element out approximately three inches and disconnected the two wires from the element.
Be careful not to let wires slip back into opening.
Attach wires to new element and carefully put back in correct position. Install two screws to secure.
Flip breaker back on. Turn oven on and show the little woman what a handyman you are! She might be so impressed she'll bake a cake.
Removed two screws that hold element in place.
Pulled element out approximately three inches and disconnected the two wires from the element.
Be careful not to let wires slip back into opening.
Attach wires to new element and carefully put back in correct position. Install two screws to secure.
Flip breaker back on. Turn oven on and show the little woman what a handyman you are! She might be so impressed she'll bake a cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Wayne, OK
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Lower heating element burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and replaced the two wires that hold the element in place. I received the part within about 36 hours after placing order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Calhoun, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Overn would not heat properly.
Turn circuit breaker off.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!
P.S. Shipping was very fast.
Two screws detached the unit.
Another two screws to disconnect the wires. Reversed above operation for installation.
Turn circuit breaker on.
All fixed!
P.S. Shipping was very fast.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- arthur from annandale, VA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Old burnt out element
Removed the two screws holding the mount and then reattached the two wires to the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Agnes from Rochester Hills, MI
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven wouldn't heat.
Shut the power off to the stove. Removed the screws and pulled the old part out. Replaced with new part from Parts Select.
Your service is excellent. I received the part within two days of it being mailed. The emails received from you were very helpful and also confirmed the transaction.
Thank you very much.
Your service is excellent. I received the part within two days of it being mailed. The emails received from you were very helpful and also confirmed the transaction.
Thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RM from Woodinville, WA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake element burned out
I got the help for the install from the help desk. It went EXACTLY as described, I'm so impressed. So got the best price and the best help and we're fixed and I'm baking again. Awesome
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from Sacramento, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The bake element burned out and broke.
It was quite easy. We first turned the power off at the main power switch. Once the power was off, we removed the two screws that fastened the metal plate in the back. We pulled the old bake element out and removed the two screws that fastened the element to two wires. To fasten the new bake element we simply reversed the procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Dallas, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Old bake element bubbled up, died.
Turned off breaker, unscrewed holding plate, unscrewed element from electric connection wires, replaced element and screwed all back together, turn on breaker, oven working fine now. E-Z!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tucson, AZ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Probe Sensor
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Venice, FL
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Replace Burned-out oven bake element
Used nut driver to remove old element and screw driver to remove power leads. Reversed process to install new element. Took about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!