JAS011J4 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Debby from Wimberley, TX
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Burner supports broke, no longer could use the burner
Cut the power off to the range, unscrewed the burner from range and pulled off the element and unscrewed the two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Yukon, OK
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
old units did not fit properly, and looked aged
followed instruction that came with the parts. Looks great and was easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Kokomo, IN
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burner not heating properly
1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J.D. from Jasper, TX
- Parts Used:
- WB30X359
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Bad Element support
Ordered part on Thursday - it arrived the next day -
I repaired the Stovetop burner the following morning.
all went well, even tho I found another element wiring
routing wrong and correct it as well while there. It's
all working well now.
I repaired the Stovetop burner the following morning.
all went well, even tho I found another element wiring
routing wrong and correct it as well while there. It's
all working well now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Brookhaven, PA
- Parts Used:
- WB32X10013, WB32X10012, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burners were burnt
replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from Gate City, VA
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old and rusted rings and pans
lift stove eyes and replace
Was this instruction helpful to you?
Thank you for voting!
Old trim rings were rusted and soiled
Too easy to describe. Just lifted out the old rings and popped in the new ones. PartSelect is my go-to source for appliance parts both for my home and my job as maintenance man for residential group homes in my area. Website is easy to use, prices are good, shipping is always surprisingly fast. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Scranton, NC
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
electric burner burned out
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Easy has falling off a log!!!!!!!!!!!!
Easy has falling off a log!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Kempner, TX
- Parts Used:
- WB32X10013, WB32X10012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls could not be cleaned
Replaced drip bowls.
Was this instruction helpful to you?
Thank you for voting!
The burner sparked and no longer worked.
I held a flashlight directly on the repair sight while my husband disconnected the old burner unit and put on the new. The extra light was essential as it's kind of dark and part of the repair takes place partly under the stove top and our bodies were blocking the light coming from above. Also pay attention to how it is put together and make a note of it before you take it apart. Other than that it was very easy to replace the bad burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alan from Tallahassee, FL
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013, WB30X359
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Replaced rusted out Burner
I have tilt up burners on my Range, and decided to replace one that have finally rusted out the part that holds it in place. Repair was easy- installed according to the enclosed instructions. Parts arrived in good condition and very timely. A+
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Delores from Carlsbad, CA
- Parts Used:
- WB30X359
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bracket under electric bruner was broken .
I followed the instruction that was enclosed with the parts and found it to be very easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from fort wayne, IN
- Parts Used:
- WB32X10013, WB32X10012, WB31X5014, WB31X5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
original trim rings
replace trim rings with the new shiny ones I got from parts select. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from High Bridge, NJ
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element ruptured and wouldn't heat
The replacement was easy: turned off breaker to range; unscrewed element from range top;opened ceramic terminal box; unscrewed element from range wires. Then I simply reversed the procedure, using the new parts. Easy to do and it only took about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RONALD W from PISCATAWAY, NJ
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Heating Element Burn Out
Easy to do . Four screws,removed cover,removed switch. Installed switch,and cover. Time 1/2 hr.
Was this instruction helpful to you?
Thank you for voting!