J312*02 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dee Ann from Oklahoma City, OK
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Coil burned out.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from North Richland Hills, TX
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
old element was not heating at all
removed it, ordered it and it only took 15 minutes to replace it.
I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.
Very quick delivery, within 3 days.
I unscrewed the two mounting bolts from the back of the oven (with the oven turned off) and then removed the two screws that connected the wire to the old element and then screwed them all in reverse order the same way I removed them.
Very quick delivery, within 3 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marc from Apple River, IL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heating element broke
Use nut driver to take off shield. Pull out element to expose element and wire connections. Use nut driver to take off the 2 little screws. Remember what side is positive(red wire) and what side is negative(black wire). Put shield over the 2 wire and reconnect to element. Will need a standard screwdriver for the new screws. Slide wires into insulation and put back on shield.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TOM from SAMMAMISH, WA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven Would Not Heat
Replaced lower element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from Riverside, CA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element was bad, no heat
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Attached the wires to the new heating element, screwed it back in. That's it.
I was glad they had the part for such an old oven.
I was glad they had the part for such an old oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Roanoke, VA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven would not heat
Same as you described
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheri from Lakeland, FL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Bottom oven coil not heating
My husband did the repair in about 15 minutes. It was apparently self explanatory and required no directions. Take the old one out and replace it the same way it came out. And viola!!, the oven works like new - all for about $33. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Gainesville, FL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heating element cracked and arcing
First I unplugged the oven from the wall. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The installation process was just as easy as the removal. Approx 10 minutes and I was cooking. BTW, the heating element was at my house the next day after ordering. Great service
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Marysville, WA
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
The bake element broke in half and did not heat after that
First I took out the oven racks removed two screws then I pulled it out a couple of inches to expose the wires and removed the screw. Put the new element in place and replaced the two screws put the wires back and replaced the two screws that hold the element in place.
My stove is over 40 years old matching the 40's - 50's style decor. in my kitchen if I had to replace the entire stove for a reproduction the cost would have been substantually more.
I didn't even have to ask my husband to do this it was easy enough to do myself.
My stove is over 40 years old matching the 40's - 50's style decor. in my kitchen if I had to replace the entire stove for a reproduction the cost would have been substantually more.
I didn't even have to ask my husband to do this it was easy enough to do myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debby from Wimberley, TX
- Parts Used:
- WB30X348
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Burner supports broke, no longer could use the burner
Cut the power off to the range, unscrewed the burner from range and pulled off the element and unscrewed the two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAMELA from RIVERVIEW, FL
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven baking element would not heat
First , for safety, I flipped breakers to kitchen applicances to cut off the power. Removed the 2 screws that held the old element in place. Pulled it out a couple of inches and disconnected the 2 wires attached to the prongs of the element. Reattached them to the new element, pushed it back in and replaced the screws. Turn power back on and voila! ... was ready to bake again! All this is a matter of 15 mins!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from Waterford, CT
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element burned out.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, put the new one in and reversed the procedure. Also delivery was great, I ordered the part and received it the next morning. I highly recommend your service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from Canal Winchester, OH
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Element had burnt out
First unplugged from wall outlet, then just removed the old element and four screws. Replaced with the new one and rescrewed in. VERY VERY EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duryea from Westminster, CO
- Parts Used:
- WB44X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burn't up element
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Installed the new element reversing the process above
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Fenton, MO
- Parts Used:
- WB44X5099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Lower Baking Element burned out - needed replacement.
Repair went fine after I got the second element shipped to me. First element sent was DOA, so I called customer service and they credited my CC for part cost and shipping, then charged the new replacement to my account and mailed it out. Got it the next day. Repair was easy - turned off power to oven took out two screws holding element in place. Unbolted the two wires from element and installed new element. Oven element heated up cherry red and I am back to baking with an oven I thought was a gonner. Was impressed with customer service replacement process. It was fast and easy with no problems. Will buy again from PartSelect.com. Thanks
Was this instruction helpful to you?
Thank you for voting!